mypros+
Model reference

Whirlpool WTW5640XW3

Washer

13 documents44 error codes19 service modes

Available documentation

Tech Sheet

  • Service Technical Sheet W1024050444 pg
    Covers this model
  • Techsheet W10468342 RevC44 pg
    Covers this model

Service Manual

  • Vertical Modular Washer84 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Service Flash

  • Service Pointer - W10411107 (Broken Lid Lock)1 pg
    Covers this model
  • Technical Service Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model
  • Service Pointer - W10405379 - Rev A (Elimination of Counter Weight)1 pg
    Covers this model
  • Technical Service Pointer - Continuous Test Mode3 pg
    Covers this model
  • Technical Service Pointer #W10492393 - Drive (Splutch) Pulley Comes Loose6 pg
    Covers this model

Tech Tip

  • Service Pointer - W10657326 (Customer Tip Sheet)3 pg
    Covers this model

Training

  • Technical Training Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model
  • Manual de referencia rapida1 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW5640XW3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (44)

CodeMeaning
F0 E0No fault codes stored in memory.F0 E2Over suds condition detectedF0 E4High water temperature detected during rinse cycle (105°F or higher).F0 E5Off balance load detected.F0E0No fault codes stored in memory.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2 E1Stuck keyF2 E3Mismatch of Main Control and UIF2E1Stuck keyF2E3Mismatch of main control and UIF3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure sensor faultF3E2Inlet water temperature faultF5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7 E1Basket speed sensor faultF7 E5Shifter fault
View all 44 error codes
F7 E6Motor faultF7 E7Motor unable to reach target RPMF7E1Basket speed sensor faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1No fill, long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F9 E1Long drainF9E1Long drain

Service modes (19)

  • Automatic Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Spin LED is On and display shows…
  • automatic_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin LED…
  • calibration["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse LED…
  • Calibration Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse LED is On and display shows…
  • diagnostic["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Fault Code Display Mode["Activate diagnostic test mode (see entry sequence above).","Turn cycle selector knob until Done…
  • fault_code_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Done LED…
  • Manual Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Spin & Done LEDs are On and…
  • manual_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Spin &…
  • Sales Demo Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse & Done LEDs are On and…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse, Spin, and Done LEDs are On…
  • sw_version_display["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are On…
  • tachometer_verification["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Wash and…
  • UI Test Mode["Activate diagnostic test mode.","Turn cycle selector knob until Rinse & Spin LEDs are On and…
  • ui_test["Enter diagnostic mode (see diagnostic entry sequence).","Turn cycle selector knob until Rinse &…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass