mypros+
Model reference

Whirlpool XCAE2765

Washer

2 documents23 error codes10 service modes

Available documentation

Tech Sheet

  • Commercial Washers Service Technical Sheet20 pg
    Covers this model

Service Flash

  • Top-Load Washer Front Panel Pad1 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool XCAE2765.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (water temperature 40.5°C /…F0E5Off balance load detected during operation.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck button; the START button has been actuated for 10 consecutive minutes.F2E3Mismatch of main control and user interface; the UI identification does not…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket, or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after the drain pump has been on for 10…

Service modes (10)

  • Calibration Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until the status LEDs show
  • Drain & Spin Cycle["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until the status LEDs show
  • Fault Code Display Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Manual Overview Test Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Quick Overview Test Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until the status LEDs show
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until the status LEDs show
  • UI (Rotary Switch) Test Mode["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until the status LEDs show

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass