mypros+
Error code reference

Bosch Washer Error Code 67

Implausible or inexistent variant coding

Bosch codesBosch washer codes

Implausible or inexistent variant coding - variant code incompatible between controls or software of controls is incompatible.

First step from the service manual

Reset error with OFF and ON, repeat variant coding, replace control(s).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 67.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 67 means on a Bosch washer

Error code 67 on a Bosch washer indicates an implausible or nonexistent variant coding condition. Variant coding is the process by which the electronic control units in the washer are programmed to recognize the specific configuration, model, and feature set of that particular appliance. When the variant code stored in one control does not match or communicate properly with another control, or when the software versions between controls are incompatible, the machine cannot confirm it is operating with a consistent and valid system configuration. The washer will halt operation and display code 67 as a protective measure.

This error most commonly surfaces after a control board has been replaced, after a software update has been applied to one control but not the other, or when a replacement part carries firmware that does not align with the existing control in the machine. In some cases, a corrupted variant coding routine caused by a power interruption during programming can also produce this fault. There are typically two controls involved: the main control board (motor control or main PCB) and the human machine interface (HMI) or user interface board, both of which must carry compatible variant codes to function together.

Diagnosing this error begins with a power cycle reset by switching the machine off and back on, followed by repeating the variant coding procedure as outlined in the programming sequence for that specific model. If the coding cannot be completed successfully or the error returns, one or both of the control boards may need to be replaced with units that carry compatible software versions. This is not a mechanical fault and involves no issues with motors, valves, or sensors.

Source: manufacturer service documentation.

Common causes of 67

  1. 01

    Mismatched replacement control board

    Part replacement

    Installing a replacement control board that carries a different software version or variant code than the existing board is the most frequent trigger for this error. The two controls cannot agree on the machine's configuration and the fault is set immediately.

  2. 02

    Incomplete or failed variant coding procedure

    Wiring / connection

    If the variant coding routine was interrupted, skipped, or not completed correctly after a repair, the control may hold an implausible or blank variant code. Repeating the coding procedure in the correct sequence can resolve this without replacing any parts.

  3. 03

    Corrupted control software from power interruption

    Wiring / connection

    A power surge or interruption during a software update or coding session can corrupt the variant code stored in one of the controls. A power cycle reset followed by a fresh coding attempt is the first step to address this.

  4. 04

    Incompatible software between main board and HMI board

    Part replacement

    The main control board and the user interface board must run software versions that are compatible with each other. If a firmware discrepancy exists between the two, error 67 will be triggered even if both boards are otherwise functional.

  5. 05

    Faulty or failed control board

    Part replacement

    In some cases, a defective control board is unable to store or transmit a valid variant code regardless of how many times the coding procedure is performed. If all other steps fail, one or both boards will need to be replaced.

See the test procedure for each cause

Frequently asked questions about 67

What does 67 mean on a Bosch washer?
Error code 67 on a Bosch washer means the machine has detected an implausible or missing variant code, or that the software versions between two of its control boards are incompatible. Variant coding is the programming that tells each control what model and feature configuration it is working with. When this information is mismatched or absent, the washer will not operate. This error often follows a control board replacement or a disrupted programming session.
Will resetting the washer clear error code 67?
A power cycle reset by turning the machine off and back on is the recommended first step and can clear the error if it was caused by a temporary software glitch. However, if the underlying cause is a mismatched or incompatible control board, the error will return after the reset. In those cases, the variant coding procedure must be repeated, or the incompatible board must be replaced.
How do I fix error code 67 on a Bosch washer?
Start by turning the washer off and back on to reset the error, then repeat the variant coding procedure for your specific model. If the error returns, check that any recently installed control board is software-compatible with the existing board in the machine. If the boards cannot be brought into alignment through coding, one or both controls will need to be replaced with units that carry compatible firmware.
Is it safe to use my Bosch washer when error code 67 appears?
The washer will typically prevent itself from running when error code 67 is active, as it cannot confirm a valid and consistent system configuration between its controls. This is a protective function rather than a sign of a hazardous condition. You should not attempt to bypass the error and should resolve the control compatibility issue before resuming normal use.
How much does it cost to repair error code 67 on a Bosch washer?
If the error is resolved simply by repeating the variant coding procedure, there may be no parts cost, though a service call to perform the programming can range from roughly 80 to 150 dollars depending on your area. If one control board needs to be replaced, parts and labor combined typically range from 200 to 500 dollars or more depending on which board is at fault and local labor rates. Replacing both control boards would increase costs further.

Related Bosch washer codes

All Bosch washer codes
View all 123 Bosch washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass