Skip to main content
Error code reference
Bosch Washer Error Codes
125 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
16Door lock open17Water filling time exceeded (conventional measurement)18Pumping time exceeded19Heating time exceeded20Unexpected heating23Aqua stop actuated25Error of Aqua Sensor (Turbidity Sensor)26Error of analogue pressure sensor27Error of offset adjustment of analogue pressure sensor28Error of flow sensor29No water filling detected by flow sensor (fast measurement)31Overflow level exceeded32Spinning interruption due to unbalance detected.34Door lock cannot be locked35Door lock cannot be unlocked36Door lock circuit defect37Error of temperature sensor: break38Error of temperature sensor: short-circuit42Uncontrolled run-up of drum motor43Drum motor does not rotate44Test of relay for changing direction of drum motor failed593D-Sensor measurement error or plausibility error60Flow sensor too low or too high values61Implausible door lock status63System error67Implausible or inexistent variant codingd:01Motor control short circuitedd:02Motor control interruptiond:03Damaged motor control temperature sensord:06Motor control NTC relay failure-NTC too hot or relay stuck closed.d:07Motor control (inverter) failed or motor shorted-faulty motor control or motor.d:08Motor speed sensor failedd:09Voltage too highd:10Power limiter switch off-motor overloaded or binding.d:11Voltage too lowd:12Motor control high current switch off-motor overloaded or binding.d:13Motor control high temperature switch off-motor overloaded or binding.d:14Motor control high temperature warning-motor overloaded or binding.d:15Power limiter warning-motor overloaded or binding.d:16Motor high temperature switch off-motor overloaded or binding.d:17Motor high temperature warning-motor overloaded or binding.d:18Peak voltage too highdr:01Motor control short circuiteddr:02Motor control interruptiondr:03Damaged motor control temperature sensordr:06NTC relay failuredr:07Motor control (inverter) failed or motor shorteddr:08Motor speed sensor faileddr:09Voltage too highdr:10Power limiter switch offdr:11Voltage too lowdr:12Motor control high current switch offdr:13Motor control high temperature switch offdr:14Motor control high temperature warningdr:15Power limiter warningdr:16Motor high temperature switch offdr:17Motor high temperature warningdr:18Peak voltage too highE:01Door open during washingE:02Door lock doesn't unlock-jammed lock or bad wire harness.E:03Door lock can't be locked-jammed lock or bad wire harness.E:04Door lock can't be unlocked-jammed lock or bad wire harnessE:05Door control brokenE:06NTC open-circuitedE:07Unexpected heating (heater on at wrong time)-faulty heater or stuck heater relay.E:08Unexpected heating (heater on at wrong time)E:09Heater doesn't shut offE:12Water supply time exceededE:13Drain pump time exceeded-faulty drain pump, wire harness, or hose.E:14No water flow within 6 minutesE:20Spinning aborted due to unbalanced loadE:21Drain pump time exceededE:22Overflow level exceededE:24Pressure sensor gives failure voltage levelE59Imbalance system defective, stored in error memory indicating a spin/imbalance fault.Er:01Door openEr:02Door lock can't be locked-jammed lock or bad wire harness.Er:03Door lock can't be unlocked-jammed lock or bad wire harness.Er:04Door control brokenEr:05NTC open-circuitedEr:06NTC shortedEr:07Unexpected heating (heater on at wrong time)Er:08Unexpected heating (heater on at wrong time)-faulty heater or stuck heater relay.Er:09Heater doesn't shut off-faulty heater or stuck heater relay.Er:10Flow meter gives wrong valuesEr:11No water flow within 6 minutes-faulty inlet valve, wire harness, or hose (WFMC64/WFXD84…Er:12No water flow within 6 minutes-faulty inlet valve, wire harness, or hose.Er:13Water supply time exceeded-faulty inlet valve, wire harness, or hose.Er:14Overflow level exceededEr:15Pressure sensor gives failure voltage levelEr:16Cannot calibrate pressure sensor-faulty pressure sensor or wire harness (WFMC64/WFXD84…Er:20Can't calibrate pressure sensor-faulty pressure sensor or wire harness.Er:21Spinning aborted due to unbalanced load-unbalanced load or faulty wire harness.Er:22Frequency synchronization failedEr:24Faulty control module-frequency synchronization failed.F:16Door lock openF:17Water filling time exceeded (conventional measurement)F:18Pumping time exceededF:19Heating time exceededF:20Unexpected heatingF:23Aqua stop actuatedF:25Error of Aqua Sensor (Turbidity Sensor)F:26Error of analogue pressure sensorF:27Error of offset adjustment of analogue pressure sensorF:28Error of flow sensorF:29No water filling detected by flow sensor (fast measurement)F:32Spinning interruption due to unbalance detected.F:34Door lock cannot be lockedF:35Door lock cannot be unlockedF:36Door lock circuit defectF:37Error of temperature sensor (NTC)F:38Error of temperature sensorF:42Uncontrolled run-up of drum motorF:43Drum motor does not rotateF:44Test of relay for changing direction of drum motor failedF:593D-Sensor measurement error or plausibility errorF:60Flow sensor too low or too high valuesF:61Implausible door lock statusF:63System errorF:67Implausible or inexistent variant codingF21Appliance starts delayed or start is delayed, typically caused by frequency fluctuations.F31Overflow condition displayed even though inlet valve, pump, or analogue sensor may not be…NTC interruptionThe NTC (temperature sensor) has an open circuit/interruption, detected during the test…NTC short circuitThe NTC (temperature sensor) has a short circuit, detected during the test programme.R00Interruption in the cable harness (supply line to water level sensor / flow sensor).
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.