mypros+
Error code reference

Cove Dishwasher Error Code 050100

Wash pump drive system

Cove codesCove dishwasher codes

Wash pump drive system: No connection.

First step from the service manual

Confirm the harness connections are tight.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 050100.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 050100 means on a Cove dishwasher

Error code 050100 on a Cove dishwasher indicates a loss of electrical connection in the wash pump drive system. The wash pump is responsible for circulating water through the spray arms during the wash cycle, and it is driven by a motor controlled through a dedicated wiring harness. When the control board detects no signal or continuity in this circuit, it throws the 050100 code and halts operation to prevent damage from running the pump dry or operating with a fault.

The most frequent root cause of this code is a loose, corroded, or disconnected harness connector between the control board and the wash pump motor. Vibration from normal use can cause connectors to back out over time, especially in units that have accumulated significant cycle counts. Before assuming the motor or board has failed, a thorough inspection of all harness connections along the wash pump circuit is the required first step.

If the connectors are confirmed tight and in good condition, the fault may lie within the wiring harness itself, such as a broken wire or damaged insulation causing an open circuit. In less common cases, the wash pump motor may have an internal failure that presents as a no-connection fault to the control board. A systematic check moving from the connector points inward toward the motor will help isolate whether the issue is in the wiring or the component itself.

Source: manufacturer service documentation.

Common causes of 050100

  1. 01

    Loose or disconnected harness connector

    Wiring / connection

    The wiring harness connector to the wash pump motor may have worked loose from vibration over time. Inspect all connectors along the wash pump circuit and press them firmly until they click into place.

  2. 02

    Corroded or damaged connector pins

    Part replacement

    Moisture inside the dishwasher cabinet can cause corrosion on the connector pins, leading to a high-resistance or open connection. Look for green or white buildup on the pins and clean or replace the affected connector.

  3. 03

    Broken or damaged wiring harness

    Part replacement

    A wire in the harness between the control board and the wash pump motor may have a break or damaged insulation, causing an open circuit. Inspect the harness routing for pinch points, chafing, or visible damage.

  4. 04

    Failed wash pump motor

    Part replacement

    If the wiring and connectors check out, the wash pump motor itself may have an internal open circuit. This would require testing the motor windings for continuity and replacing the motor if it fails that test.

  5. 05

    Control board fault

    Part replacement

    In rare cases, the control board may fail to properly send or read signals on the wash pump drive circuit even when the pump and wiring are intact. This is the least likely cause and should only be considered after all other components are ruled out.

See the test procedure for each cause

Frequently asked questions about 050100

What does 050100 mean on a Cove dishwasher?
Error code 050100 on a Cove dishwasher signals a loss of connection in the wash pump drive system. The control board is not detecting a valid electrical connection to the wash pump motor, so the dishwasher stops the cycle to prevent damage. The issue is most often a loose or disconnected wiring harness connector rather than a failed component.
Can I fix error code 050100 myself?
In many cases, yes. The recommended first step is to check that all harness connectors related to the wash pump are fully seated and free of corrosion. If tightening the connections resolves the fault, no parts are needed. If the issue is a broken wire, damaged connector, or failed pump motor, those repairs are more involved and may benefit from a qualified technician.
Is it safe to keep using my Cove dishwasher with error code 050100?
No, the dishwasher should not be run while displaying this error. The code indicates the wash pump is not functioning correctly, meaning water will not circulate properly during the cycle. Running the machine in this state could result in incomplete cleaning and may cause further component damage.
How much does it cost to repair error code 050100 on a Cove dishwasher?
Repair costs vary depending on the cause. If the fix is simply reseating a loose connector, there may be no parts cost at all. A wiring harness repair or connector replacement is generally in the range of $50 to $150 in parts. If the wash pump motor requires replacement, expect parts and labor costs to range from $200 to $500 or more depending on your location and service provider.
Will resetting my Cove dishwasher clear error code 050100?
A reset may temporarily clear the code, but it will return as soon as the dishwasher attempts to run a wash cycle and cannot establish connection with the pump motor. The underlying electrical connection issue must be identified and corrected for the code to be permanently resolved.

Related Cove dishwasher codes

All Cove dishwasher codes
View all 62 Cove dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass