mypros+
Error code reference

Cove Dishwasher Error Code 050103

Wash pump drive system

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 050103 error code actually means

Your Cove dishwasher has detected an internal electronics failure in the module that controls the wash pump motor. This is a hardware-level problem inside the control board itself, not something caused by a clog or a simple sensor issue. A technician will need to replace the motor control module to get the dishwasher working again.

Diagnostic procedure

The full 050103 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace the MCM assembly.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 050103 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 050103

Ranked by how often they cause this code
  1. 1Failed MCM assembly (internal ADC fault)
  2. 2Voltage transient damage to MCM board
  3. 3MCM assembly connection or seating issue
  4. 4MCM component degradation over time

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 050103

What does 050103 mean on a Cove dishwasher?
Error code 050103 indicates a hardware fault in the Analog-to-Digital Converter (ADC) circuit within the wash pump drive system. This ADC is part of the Motor Control Module (MCM) assembly and is responsible for converting analog motor feedback signals into usable digital data. When the ADC hardware fails, the dishwasher cannot properly control or monitor the wash pump, and the error is triggered. Replacement of the MCM assembly is required to resolve the fault.
Is it safe to use my Cove dishwasher while error 050103 is active?
It is not advisable to continue using the dishwasher with this error active. The fault indicates the MCM cannot reliably control the wash pump, which means the dishwasher may not complete cycles correctly or may shut down mid-cycle. Running the unit in this state could also place additional stress on other components.
How much does it cost to repair error code 050103 on a Cove dishwasher?
Repair costs will vary depending on parts pricing and labor rates in your area. The primary cost is the MCM assembly itself, which is a specialized control board component, plus any applicable labor charges if a technician performs the replacement. As a general range, expect total repair costs to fall somewhere between $200 and $600 depending on part availability and service rates in your region.
Can I fix error code 050103 myself?
Resolving this error requires replacing the MCM assembly, which involves working with the dishwasher's internal electronics and electrical connections. Knowledgeable DIYers with experience in appliance repair may be able to perform the swap, but the job does require proper precautions including disconnecting power before beginning. If you are not comfortable working with appliance control boards and wiring harnesses, a qualified technician is recommended.
Will resetting the dishwasher clear error code 050103?
A reset is unlikely to permanently clear error 050103 because the fault is rooted in a hardware failure inside the MCM assembly. Even if a reset temporarily clears the displayed code, the underlying ADC circuit fault remains, and the error will return once the dishwasher attempts to run the wash pump drive system. The MCM assembly must be replaced to resolve the issue.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass