mypros+
Error code reference

Electrolux Ice Maker Error Code Er

Bail Arm Switch test error

Electrolux codesElectrolux ice maker codes

Bail Arm Switch test error — one or both bail arm switch conditions were not met during diagnostic test 58C.

First step from the service manual

First perform Test 63C and follow troubleshooting procedures for 63C; if 63C passes, perform 58C — if 58C fails, replace Ice Maker Assembly (243297603).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Er.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Er means on a Electrolux ice maker

The Er error code on an Electrolux ice maker indicates a bail arm switch test failure detected during diagnostic test 58C. The bail arm is the wire arm that rides on top of the ice pile in the storage bin. When the ice level rises and lifts the arm, the switch signals the ice maker to stop production. When ice is removed and the arm drops, production resumes. During test 58C, the control module sequences through specific bail arm switch conditions, both the raised and lowered positions, and if one or both of those conditions are not confirmed within the expected parameters, the Er code is triggered.

Before condemning the ice maker assembly itself, the diagnostic sequence requires performing test 63C first. Test 63C evaluates related upstream conditions and wiring that could interfere with the bail arm switch circuit. If test 63C fails, its troubleshooting path takes priority and must be resolved before retesting. Only when 63C passes and 58C still fails does the fault clearly point to the ice maker assembly as the source of the problem.

A failed test 58C after a passing 63C indicates the bail arm switch inside the ice maker assembly is not completing the required circuit states during the diagnostic cycle. This can result from a mechanically stuck or damaged bail arm, a faulty switch that does not actuate or release properly, or internal wiring failures within the assembly. Because the switch is integrated into the ice maker assembly (part number 243297603), the entire assembly is replaced rather than the switch individually.

Source: manufacturer service documentation.

Common causes of Er

  1. 01

    Faulty bail arm switch inside the ice maker assembly

    Part replacement

    The switch that detects the arm position may have failed internally and no longer signals both the raised and lowered states correctly during test 58C. This is the most common root cause when test 63C passes but 58C fails.

  2. 02

    Mechanically stuck or damaged bail arm

    Wiring / connection

    The bail arm itself may be bent, broken, or obstructed by ice buildup, preventing it from moving freely through its full range of motion. Inspect the arm for physical damage or ice jamming it in one position.

  3. 03

    Wiring or connection fault in the bail arm switch circuit

    Wiring / connection

    A damaged wire, loose connector, or corroded terminal in the circuit between the bail arm switch and the control board can cause the switch signal to read incorrectly. Test 63C is specifically designed to identify this condition before proceeding to 58C.

  4. 04

    Control board not receiving switch state changes

    Part replacement

    If the control module is not properly interpreting the switch signals during the diagnostic cycle, it may log the Er code even if the switch itself is functioning. This is less common and is typically ruled out by the 63C and 58C diagnostic sequence.

See the test procedure for each cause

Frequently asked questions about Er

What does Er mean on a Electrolux ice_maker?
The Er code indicates that the bail arm switch failed its diagnostic test during test 58C. The bail arm switch is responsible for detecting when the ice bin is full and stopping ice production. One or both of the required switch positions were not confirmed during the test. This points to a problem with the bail arm mechanism or the switch itself within the ice maker assembly.
Can I fix the Er error on my Electrolux ice maker myself?
Some basic checks are possible without tools, such as inspecting the bail arm for ice buildup or physical damage that could prevent it from moving freely. However, the full diagnosis requires running tests 63C and 58C using the machine's diagnostic mode, which is best suited for technicians familiar with the procedure. If both tests confirm the ice maker assembly is at fault, replacing the assembly (243297603) is the required repair. Attempting assembly replacement without completing the diagnostic sequence may result in replacing a part that was not actually defective.
Is it safe to use my Electrolux ice maker while the Er code is displayed?
The Er code indicates the ice level detection system is not functioning reliably, which means the ice maker may not know when to stop production. Running the unit in this condition risks ice overflow into the freezer compartment. It is best to stop ice maker operation until the fault is diagnosed and repaired.
How much does it cost to repair the Er error on an Electrolux ice maker?
If the repair requires replacing the ice maker assembly, parts typically range from around 80 dollars to 150 dollars depending on the supplier, with professional labor adding another 75 to 150 dollars in most cases. If the issue is only a wiring or connector problem identified during test 63C, the repair cost could be lower. Getting a diagnosis first helps avoid paying for parts that are not needed.
Will resetting my Electrolux ice maker clear the Er error code?
A reset may temporarily clear the Er code from the display, but it will not resolve the underlying hardware fault with the bail arm switch. The code is likely to return once the ice maker runs through its next cycle and the diagnostic conditions are not met again. A proper repair requires running tests 63C and 58C and addressing the root cause identified by those tests.

Related Electrolux ice maker codes

All Electrolux ice maker codes
View all 18 Electrolux ice maker codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass