mypros+
Error code reference

Electrolux Oven Error Code bAtt

Battery is low on the UI board due to ageing.

Electrolux codesElectrolux oven codes

Battery is low on the UI board due to ageing.

First step from the service manual

Replace the CR2032 type battery on the UI board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for bAtt.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What bAtt means on a Electrolux oven

The bAtt error code on an Electrolux oven indicates that the coin cell battery on the user interface (UI) board has dropped below the voltage threshold required for reliable operation. The UI board uses a CR2032 lithium coin cell battery to retain settings such as the clock and certain user preferences when the oven is disconnected from main power. When this battery ages and its voltage degrades, the board detects the low-power condition and triggers the bAtt alert to notify the user or technician.

CR2032 batteries have a nominal voltage of 3 volts and a typical service life of several years, depending on usage patterns and storage conditions. Over time, the cell's internal chemistry depletes and output voltage drops. The UI board's monitoring circuit compares the battery voltage against a reference threshold, and once the voltage falls below that threshold, the bAtt code is set. This is a normal aging failure rather than a fault caused by a defective board or wiring problem.

The primary and essentially only corrective action is to replace the CR2032 battery on the UI board. This involves accessing the UI board, locating the coin cell holder, and installing a fresh CR2032 cell. After replacement, the error code should clear and normal board operation, including clock retention, will be restored. No additional component repairs are typically needed when the board itself is functioning correctly and only the battery has depleted.

Source: manufacturer service documentation.

Common causes of bAtt

  1. 01

    Normal CR2032 battery aging

    Part replacement

    The CR2032 coin cell on the UI board depletes naturally over several years of use. This is the most common and expected cause of the bAtt code.

  2. 02

    Battery stored or used in high-temperature environment

    Part replacement

    Prolonged exposure to elevated ambient temperatures near the oven cavity can accelerate battery discharge, causing it to fail sooner than expected.

  3. 03

    Battery seated incorrectly in the holder

    Wiring / connection

    If the CR2032 was previously replaced and not fully seated, poor contact can cause a low-voltage reading. Check that the battery is firmly pressed into the coin cell holder with correct polarity.

  4. 04

    Defective replacement battery

    Part replacement

    A new CR2032 that was improperly stored or is counterfeit may arrive with insufficient charge. If the bAtt code returns shortly after replacement, try a battery from a different brand or supplier.

See the test procedure for each cause

Frequently asked questions about bAtt

What does bAtt mean on a Electrolux oven?
The bAtt code means the CR2032 coin cell battery on the oven's user interface board is low due to aging. This battery maintains clock and settings data when the oven loses power. The code is a maintenance alert rather than a component failure, and replacing the battery clears it. The oven's core cooking functions are not affected by this battery.
How do I fix the bAtt error on my Electrolux oven?
The fix is to replace the CR2032 coin cell battery located on the UI board inside the oven's control panel. Access to the UI board typically requires removing the control panel housing. Once the old battery is removed and a new CR2032 is installed with correct polarity, the bAtt code should clear on its own or after restoring power.
Will resetting the oven clear the bAtt error code?
Resetting the oven by cycling the power will not permanently clear the bAtt code. Because the underlying cause is a depleted battery, the code will return after a reset. The only way to resolve it is to replace the CR2032 battery on the UI board.
Is the bAtt error on an Electrolux oven a safety concern?
No, the bAtt code is not a safety issue. It relates only to the small backup battery that retains settings and the clock, not to any heating, gas, or electrical safety system. The oven can continue to operate normally for cooking while this code is present, though clock and preference settings may be lost if power is interrupted.
How much does it cost to fix the bAtt error on an Electrolux oven?
If you replace the CR2032 battery yourself, the cost is minimal, typically between $1 and $5 for the battery. If a technician is needed to access the UI board and perform the replacement, expect to pay a service call fee plus labor, which can range from $75 to $200 depending on your location and the service provider.

Related Electrolux oven codes

All Electrolux oven codes
View all 186 Electrolux oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass