mypros+
Error code reference

Electrolux Range Error Code 3,4

Incorrect Micro ID

Electrolux codesElectrolux range codes

Incorrect Micro ID - Internal microprocessor identification failure.

First step from the service manual

Replace electronic control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 3,4.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 3,4 means on a Electrolux range

Error code 3,4 on an Electrolux range indicates an Incorrect Micro ID, which is an internal microprocessor identification failure. This fault originates within the electronic control board itself. The control board contains a microprocessor that carries a specific embedded identification code, and when the board's internal self-diagnostic routine cannot verify that ID correctly, it generates this error. This is not a sensor fault or a wiring fault in the traditional sense; it points directly to a failure at the processor or firmware level inside the control board assembly.

The most likely cause is a corrupted or failed microprocessor on the control board. This can result from power surge damage, a partial component failure on the board, or a manufacturing defect that has developed over time. Because the microprocessor ID is embedded in the hardware, there is no field-level way to reprogram or restore it. The control board must be treated as a failed unit.

Because this fault is internal to the board, external diagnostics such as checking wiring harness continuity or testing individual sensors will not resolve the error. The first and only recommended diagnostic step is to replace the electronic control board. Once a new board is installed with the correct microprocessor ID for the range model, the fault should clear and normal operation should resume.

Source: manufacturer service documentation.

Common causes of 3,4

  1. 01

    Failed electronic control board microprocessor

    Part replacement

    The microprocessor on the control board has failed or its embedded identification code has become corrupted, causing the self-diagnostic routine to generate the 3,4 error. This is the primary cause and replacement of the control board is required.

  2. 02

    Power surge damage to the control board

    Part replacement

    A voltage spike or power surge can damage the microprocessor or related components on the control board, leading to an ID verification failure. Check the board visually for signs of burned components or discoloration.

  3. 03

    Intermittent power interruption during board operation

    Wiring / connection

    A sudden loss of power while the board is processing can occasionally corrupt internal state and trigger this fault. Attempting a hard reset by disconnecting power for several minutes is worth trying before committing to a board replacement.

  4. 04

    Manufacturing defect or end-of-life board failure

    Part replacement

    Electronic control boards can fail due to component degradation over time or latent manufacturing defects. If the range is older or has had prior control board issues, this is a likely explanation.

See the test procedure for each cause

Frequently asked questions about 3,4

What does 3,4 mean on a Electrolux range?
Error code 3,4 on an Electrolux range means the electronic control board has detected an Incorrect Micro ID, which is an internal microprocessor identification failure. The board's self-diagnostic routine cannot verify the embedded processor ID, indicating a hardware-level fault within the control board itself. This error cannot be resolved by checking external wiring or sensors, and the control board typically needs to be replaced.
Can I fix error code 3,4 on my Electrolux range myself?
A DIYer with basic appliance repair experience can attempt this repair by replacing the electronic control board. Before purchasing a new board, try disconnecting power to the range for several minutes to see if the error clears on its own. If the error returns, the control board will need to be replaced with a compatible unit for your specific model.
Is it safe to use my Electrolux range while error code 3,4 is displayed?
Because error 3,4 indicates an internal control board failure, the range's ability to properly manage cooking functions, temperature regulation, and safety shutoffs may be compromised. It is not recommended to continue using the range until the control board has been inspected and replaced. Relying on a faulty control board could result in unpredictable operation.
How much does it cost to fix error code 3,4 on an Electrolux range?
The cost to repair this error depends primarily on the price of the replacement electronic control board and whether you hire a technician or complete the repair yourself. Control board replacements for Electrolux ranges typically range from around $150 to $400 or more for the part alone, depending on the model. Adding professional labor can bring the total repair cost to between $250 and $600 or higher.
Will resetting my Electrolux range clear error code 3,4?
A power reset, performed by unplugging the range or turning off the circuit breaker for several minutes, is worth attempting as a first step. However, because error 3,4 is caused by an internal microprocessor identification failure within the control board, a reset is unlikely to provide a permanent fix. If the error reappears after resetting, the control board will need to be replaced.

Related Electrolux range codes

All Electrolux range codes
View all 175 Electrolux range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass