Skip to main content
Error code reference
Electrolux Range Error Codes
178 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1,2Runaway Temperature1,2,3Max Unlock Time Exceeded (Motor Door Latch)1,2,3,4Runaway Temperature1,2,3,4,5Incorrect Micro ID1,2,3,4,5,6,7Incorrect EEPROM Checksum1,3Open Temperature Probe1,4Shorted Temperature Probe1,5Max Lock Time Exceeded (Motor Door Latch)11Jammed key on ESEC cooktop control.2,3,6Max Lock Time Exceeded (Motor Door Latch)2,4Shorted temperature probe2,5Inter processor communications failure on motor door latch.2,6Max Unlock Time Exceeded (Motor Door Latch)21LIN (Local Interconnect Network) error, no communications or shorted bus on ESEC cooktop.3,4Incorrect Micro ID3,5Max unlock time exceeded on motor door latch mechanism.3,6Max Unlock Attempts Exceeded (Motor Door Latch)3,7Motor Door Latch Failed During Clean Operation30AC input voltage too high at Induction Housing Assembly.31Internal generator error, sync Induction Housing Assembly / Left side cooking zones.32Power supply defect, Induction Housing Assembly / Left side cooking zones.33Power supply defect, Induction Housing Assembly / Left side cooking zones.39Configuration mismatch between the ESEC-UIB and the Induction Housing Assembly.4,5Max unlock attempts exceeded on motor door latch mechanism.4,5,6Max Unlock Attempts Exceeded (Motor Door Latch)4,6Max Lock Attempts Exceeded (Motor Door Latch)4,7Inter Processor Communications Failure (Motor Door Latch)5,6Motor Door Latch Failed During Clean Operation5,6,7Inter Processor Communications Failure (Motor Door Latch)51Inductor temperature sensor break (Left Front).52Inductor temperature sensor break (Left Rear).54Inductor temperature sensor break (Right Rear).55Inductor temperature sensor break (Right Front).6,7Max lock attempts exceeded on motor door latch mechanism.61Left Front inductor temperature sensor too hot.62Left Rear inductor temperature sensor too hot.64Right Rear inductor temperature sensor too hot.65Right Front inductor temperature sensor too hot.70AC input voltage too high, Induction Housing Assembly.71Internal generator error, sync, Induction Housing Assembly / Right side cooking zones.72Power supply defect, Induction Housing Assembly / Right side cooking zones.73Power supply defect, Induction Housing Assembly / Right side cooking zones.74Internal generator error, communication, Induction Housing Assembly / Right side cooking…75AC input voltage too low, Induction Housing Assembly.76Communication error, Induction Housing Assembly / Right side cooking zones.77Heat sink temperature sensor break, Induction Housing Assembly / Right side cooking zones.Bake + Clean (LEDs 1,5)Incorrect EEPROM Checksum detected on the electronic control board.Bake + Convection Bake + Convection Roast + Broil (LEDs 1,2,3,4)Runaway temperature condition detected in the oven.Bake + Convection Bake + Convection Roast + Broil + Clean (LEDs 1,2,3,4,5)Inter-processor communications failure on motor door latch.Bake + Convection Bake + Lock (LEDs 1,2,6)Maximum unlock time exceeded on motor door latch.Bake + Convection Roast + Lock (LEDs 1,3,6)Maximum lock time exceeded on motor door latch.Broil + Clean (LEDs 4,5)Incorrect Micro ID detected on the electronic control board.C-21Oven sensor openedC-22Oven sensor shortedC-23Oven heating overC-31PCB temp sensor openedC-32PCB temp sensor shortedC-33PCB temp over/under during self-cleanC-d1Shorted keyC-d2Door locking failureCFCheck Food reminderClean + Lock + Remove Racks (LEDs 5,6,7)Motor door latch failed during clean operation.CLnSelf-clean cycle is active.Convection Bake + Broil + Lock (LEDs 2,4,6)Maximum lock attempts exceeded on motor door latch.Convection Bake + Clean (LEDs 2,5)Open temperature probe circuit detected.Convection Roast + Broil + Lock (LEDs 3,4,6)Maximum unlock attempts exceeded on motor door latch.Convection Roast + Clean (LEDs 3,5)Shorted temperature probe circuit detected.d-OThe oven door has been open for 30 seconds during a cooking mode that requires the door…dEFDefrost mode is active.doorControl thinks the lock switch is open when oven is programmed for clean (36-inch gas…drOven door is open when attempting to set the Self-Cleaning feature.E013Bad EEPROM on ESEC.E014Loss of Display tail #0 on ESEC.E015Loss of Display tail #1 on ESECE11Shorted Keypad on the ESEC (Electronic Surface Element Control).E13Cooktop control has detected a fault or error condition.E14TST/Display tail missing; connection issue between UIB and glass touch panel.E15ESEC self test failed, or thermal cutoff open; may indicate the User Interface Board is…E21Communication failure between the filter board and UIB.E30Synchronization failureE31Synchronization failureE32Power supply defectE33Power supply defectE34Internal communication failureE35AC Input voltage too high.E36Communication error (left cooking zones).E37Heat sink temp sensor break (left cooking zones).E39Configuration mismatch between the UIB and the filter board (can occur when a filter…E51Surface unit temp sensor breakE52Surface unit temp sensor breakE54Surface unit temp sensor breakE55Surface unit temp sensor breakE61Surface unit sensor too hotE62Surface unit sensor too hotE64Surface unit sensor too hotE65Surface unit sensor too hotE70Synchronization failureE71Synchronization failureE72Power supply defectE73Power supply defectE74Internal communication failureE75AC Input voltage too high.E76Communication error (right cooking zones).E77Heat sink temp sensor break (right cooking zones).EndEnd of cycleEO63Cooktop overheating error code, typically occurs when using the griddle at high setting…EO64Cooktop overheating error code, typically occurs when using the griddle at high setting…ErESEC control has detected a fault condition, typically caused by surface control knobs…FElectronic control has detected a fault condition; an 'F' error code is displayed with a…F001Touch panel failure.F002Touch panel failure.F003The oven user interface board is incorrectly configured.F004Touch panel failure.F005Touch panel failure.F010Oven temperature runawayF011Stuck keyF012Keyboard configuration alarmF013Data written to non-volatile memory has failed verification.F015Keyboard error.F017The oven user interface board is unable to configure the touch panel.F018Oven relay board failure (wiggler).F019The oven user interface board is unable to configure the oven relay board.F022Communication failure between the oven user interface board and the oven relay board.F023Communication failure between the oven user interface board and the glass touch panel.F025The communication between the oven user interface and the oven relay board cannot be…F027The communication between the oven user interface and the oven relay board cannot be…F028The communication between the oven user interface and the touch panel cannot be initiated.F029The communication between the oven user interface and the touch panel cannot be initiated.F030Open oven temperature sensor (RTD).F031Shorted oven temperature probe (RTD).F033Meat probe temperature sensor shorted or too hot.F050The oven relay board is unable to read the status of the switches (door, MDL).F090Motor Door Lock mechanism failureF095Motor Door Lock mechanism failureF096The oven door has been detected open during a Self-Clean cycle.F1Electronic oven controller has detected a fault condition in its internal circuitry or…F10Control has sensed a potential runaway oven overheating condition; control may have…F11Shorted keyF13Oven control fault code error detected by the oven control.F14Misconnected keyboard cable between display board and touch panel.F15Controller self check failed or terminal cutoff open; may indicate the oven controller is…F2Electronic oven controller has detected a fault condition in its internal circuitry or…F20The oven controller has detected a problem with the communication link to the surface…F23The controller failed to communicate with the convection fan and oven lights control…F25No zero cross signal detected on the convection fan and oven lights control board.F3Electronic oven controller has detected a fault condition in its internal circuitry or…F30The oven control system has detected a fault or anomaly (example code shown; any code…F31Shorted RTD sensor probe or wiring problem (displayed when oven is in active mode or an…F4Electronic control has detected a fault condition.F5Indicates a harness, mother board, or user interface board failure in the ESEC 5…F6Communication failure between the mother board and the electronic oven control in the…F62Missing zero-cross signal.F7ESEC 5 failureF8Electronic control has detected a fault condition.F9Electronic oven controller has detected a fault condition in its internal circuitry or…F90Door motor mechanism failureF95Door motor mechanism failureHEHot Element indicatorHotOven temperature is still too hot to safely open the door (displayed after self-clean…LEDs 1,2Runaway TemperatureLEDs 1,2,7Max Lock Time Exceeded (Motor Door Latch)LEDs 1,7Max Unlock Attempts Exceeded (Motor Door Latch)LEDs 2,3Incorrect Micro IDLEDs 2,3,7Max Lock Attempts Exceeded (Motor Door Latch)LEDs 3,4Incorrect EEPROM ChecksumLEDs 3,4,7Motor Door Latch Failed During Clean OperationLEDs 4,5Open Temperature ProbeLEDs 4,5,7Inter Processor Communications Failure (Motor Door Latch)LEDs 5,6Shorted Temperature ProbeLEDs 6,7Max Unlock Time Exceeded (Motor Door Latch)LOCControl lock is activePbPan detection errorPFPower failure indicator; displayed when the range is first plugged in or after a power…SAbSabbath mode is active.SCCSelf Clean Cancel-the Self Clean Cancel TCO opened due to excessive cooktop temperatures…SdDemo/showroom mode is active.SFSabbath FailureSPrSelf-clean cycle was cancelled (e.g., by igniting a surface burner during self-clean on…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Electrolux error codes
Common questions
How do I find the error code on my Electrolux Range?
Most Electrolux ranges show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Electrolux ranges. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.