All Electrolux error codes

Electrolux Cooktop Error Codes

135 error codes for Electrolux cooktop models. Each links to the full diagnostic procedure from the service manual.

CodeDescription

10Center zone control defective or key sensor defective.11Center zone control defective or On/Off key sensor defective.12Center zone control or On/Off key sensor defective.14RR zone control defective or key sensor defective.15RR zone control defective or On/Off key sensor defective.16RR zone control or On/Off key sensor defective.17RF zone control defective or key sensor defective.18RF zone control defective or On/Off key sensor defective.19RF zone control or On/Off key sensor defective.2LF zone control defective or key sensor defective.21Timer or key sensor defective.22Timer or On/Off key sensor defective.23Keep Warm key sensor defective or On/Off key sensor defective.24Lock key sensor defective or On/Off key sensor defective.25Main POWER On/Off key sensor defective.3LF zone control defective or On/Off key sensor defective.30Improper power supply (high voltage) or jumper connections.31Power level failure.32Low voltage output from 12V supply on filter board.33Improper voltage output from 5V filter board.

MyPros+ Max

Get the full diagnostic procedure for any Electrolux cooktop error code.

Step-by-step tests with expected resistance, voltage, and continuity values
Wiring diagram references and connector pinouts
Verified part numbers when replacement is required

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Electrolux Cooktop

10 on my Electrolux Cooktop

M+

Center zone control defective or key sensor

From Service Manual 671129, p.21:

1.Test cables & connections. If they are good, replace center Touch Control Board.

2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.

3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.

Part 5304504863

Electronic control board

34Communication failure between filter board and power boards.35Improper power supply (low voltage) or jumper connections.36Communication error between main touch control and filter board.39Touch control board software configuration does not match the filter board 4LF zone control or On/Off key sensor defective.40Communication failure between main touch control and filter board.51Element temperature sensor break (LF).52Element temperature sensor break (LR).53Element temperature sensor break (Center).54Element temperature sensor break (RR).55Element temperature sensor break (RF).6LR zone control defective or key sensor defective.7LR zone control defective or On/Off key sensor defective.8LR zone control or On/Off key sensor defective.EGeneral error code displayed on element screens (E) while the main controller…E00Error code displayed as E on cooking zone displays and 00 on main control…E011Jammed key detected on the touch panel.E014Touch Panel Tail missing.E015ESEC self test failure.E021LIN (Local Interconnect Network) error, no communications, shorted bus.E03Error code displayed as E on cooking zone displays and 03 on main control…E030AC input voltage too high, Induction Housing Assembly (left side).E031Internal generator error, sync, Induction Housing Assembly / Left side cooking…E032Power supply defect, Induction Housing Assembly / Left side cooking zones.E033Power supply defect, Induction Housing Assembly / Left side cooking zones.E034Internal generator error, communication, Induction Housing Assembly / Left side…E035AC input voltage too low, Induction Housing Assembly (left side).E036Communication error, Induction Housing Assembly / Left side cooking zones.E037Heat sink temperature sensor break, Induction Housing Assembly / Left side…E039Configuration mismatch between the ESEC-UIB and the Induction Housing Assembly…E04Error code displayed as E on cooking zone displays and 04 on main control…E05Error code displayed as E on cooking zone displays and 05 on main control…E051Inductor temperature sensor break (Left Front).E052Inductor temperature sensor break (Left Rear).E054Inductor temperature sensor break (Right Rear).E055Inductor temperature sensor break (Right Front).E06Error code displayed as E on cooking zone displays and 06 on main control…E061Left Front inductor temperature sensor too hot.E062Left Rear inductor temperature sensor too hot.E064Right Rear inductor temperature sensor too hot.E065Right Front inductor temperature sensor too hot.E07Error code displayed as E on cooking zone displays and 07 on main control…E070AC input voltage too high, Induction Housing Assembly (right side).E071Internal generator error, sync, Induction Housing Assembly / Right side cooking…E072Power supply defect, Induction Housing Assembly / Right side cooking zones.E073Power supply defect, Induction Housing Assembly / Right side cooking zones.E074Internal generator error, communication, Induction Housing Assembly / Right…E075AC input voltage too low, Induction Housing Assembly (right side).E076Communication error, Induction Housing Assembly / Right side cooking zones.E077Heat sink temperature sensor break, Induction Housing Assembly / Right side…E10Center zone control defective key sensor.E11Center zone control defective key sensor.E12Center zone control key sensor defective.E14Right Rear zone control defective key sensor.E15Right Rear zone control defective key sensor.E16Right Rear zone control key sensor defective.E17Right Front zone control key sensor defective.E18Right Front zone control key sensor defective.E19Right Front zone control key sensor defective.E2Left Front zone control defective key sensor.E21Timer key sensor defective.E22Timer key sensor defective.E23Keep warm key sensor defective.E24Lock key sensor defective.E25Main power key sensor defective.E3Left Front zone control defective key sensor.E30AC input voltage too high at the 3 cook zones induction module.E31Internal generator error, sync in the 3 cook zones induction module / left side…E32Low voltage output from 12V supply on filter board in the 3 cook zone induction…E33Improper voltage output from filter board in the 3 cook zone induction module.E34Communication failure between filter board and power boards in the 3 cook zones…E35AC input voltage too low in the 3 cook zones induction module.E36Communication error between main touch control and filter board (3 cook zones…E37Heat sink temperature sensor break (3 zones induction module / left side…E39Configuration mismatch between the User Interface and the induction module…E4Left Front zone control key sensor defective.E40Communication failure between main touch control and filter board.E45Incoming power supply low voltage.E51Left Front element temperature sensor break.E52Left Rear element temperature sensor break.E53Center element temperature sensor break.E54Right Rear element temperature sensor break.E55Right Front element temperature sensor break.E6Left Rear zone control defective key sensor.E60Touch control general hardware error, keys.E61Left Front element temperature sensor too hot.E62Left Rear element temperature sensor too hot.E63Center element temperature sensor too hot.E64Right Rear element temperature sensor too hot.E65Right Front element temperature sensor too hot.E7Left Rear zone control defective key sensor.E70AC input voltage too high at the 3 cook zones induction module (same as E30).E71Internal generator error, sync (center cooking zone).E72Low voltage output from 12V supply on filter board in the 3 cook zone induction…E73Improper voltage output from filter board in the 3 cook zone induction module…E74Internal generator error, communication (3 zones induction module).E75AC input voltage too low in the 3 cook zones induction module (same as E35).E76Communication error in the 3 cook zones induction module for the center cooking…E77Heat sink temperature sensor break in the 3 cook zones induction module for the…E8Left Rear zone control key sensor defective.E80Flash/ROM check fail (EEPROM data).E90AC input voltage too high in the 2 cook zones induction module.E91Internal generator error, sync in the 2 cook zones induction module.E9212V on the service section too low in the 2 cook zones induction module.E935V overcurrent on the switched 5V on the service section (2 zones induction…E94Internal generator error, communication in the 2 cook zones induction module.E95AC input voltage too low in the 2 cook zones induction module.E96Communication error in the 2 cook zones induction module.E97Heat sink temperature sensor break in the 2 cook zones induction module.FInduction element utensil detection error FXXGeneral error code indicated when element displays show 'F' and the main…HResidual heat indicator displayed on cooking zone screen after the zone has…HEHot Element indicator displayed and flashing on ESEC screen after an element is…PFPower Failure indicator displayed on ESEC screen when the appliance is first…SFSabbath mode power failure recovery indicator

Start diagnosing faster today.

$29/month · Cancel anytime · Or $9.95 3-day pass