mypros+
Error code reference

Electrolux Cooktop Error Code 31

Power level failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 31 error code actually means

Error 31 means your Electrolux cooktop has lost the ability to control its power levels properly. This is usually caused by a wiring issue or a failed electronic control board inside the cooktop. The cooktop shuts itself down to prevent unsafe operation until the problem is repaired.

Diagnostic procedure

The full 31 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check wire harness (Blue & Black) from filterboard to power board. Replace power board. Replace filter board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 31 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 31

Ranked by how often they cause this code
  1. 1Faulty or damaged wire harness (Blue and Black wires)
  2. 2Failed power board
  3. 3Failed filter board
  4. 4Loose or disconnected board connectors

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 31

What does 31 mean on a Electrolux cooktop?
Error code 31 on an Electrolux cooktop signals a power level failure. This means the cooktop's control system cannot properly regulate or communicate power output to the cooking elements. The fault originates in the circuit path between the filter board and the power board, including the wire harness that connects them. The cooktop will not operate normally until the underlying cause is identified and corrected.
Is it safe to use my Electrolux cooktop when error 31 is displayed?
No, you should not attempt to use the cooktop while error 31 is active. The fault indicates the cooktop cannot properly control power levels, which means cooking elements may not respond correctly to your settings. Continuing to use the appliance in this state is a safety risk. Discontinue use and have the cooktop diagnosed before operating it again.
How much does it cost to repair error 31 on an Electrolux cooktop?
Repair costs depend on which component has failed. If only the wire harness needs repair or reseating, costs are minimal. A replacement power board typically runs in the range of $100 to $250 for the part, while a filter board may cost $80 to $200, with labor costs added if a technician performs the repair. Getting a diagnostic estimate from a qualified technician before committing to parts replacement is advisable.
Can I fix error code 31 on my Electrolux cooktop myself?
A knowledgeable DIYer can inspect the Blue and Black wire harness between the filter board and power board for visible damage, loose connectors, or corrosion without advanced tools. However, replacing the power board or filter board involves working with high-voltage components and requires comfort with appliance disassembly. If you are not experienced with internal appliance repair, a qualified technician should perform the board-level diagnostics and replacement.
Will resetting the cooktop clear error code 31?
A power reset by switching off the circuit breaker for 30 to 60 seconds may temporarily clear the display, but error 31 will return if the underlying hardware fault is not corrected. The code is caused by a physical failure in the wire harness or one of the control boards, not a software glitch. A reset alone is not a repair and should not be relied upon as a solution.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass