mypros+
Error code reference

Electrolux Cooktop Error Code E6

Left Rear zone control defective key sensor.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E6 error code actually means

Your Electrolux cooktop has detected a problem with the touch sensor for the left rear burner, meaning that control is not working correctly and the cooktop has shut it down for safety. This could be caused by a loose wire connection or a failed touch control panel. A technician will need to inspect the wiring and likely replace the touch control panel on the left side of the cooktop.

Diagnostic procedure

The full E6 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Test cables and connections between left side cook zones control and main power control. Replace left side cook zones touch control.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E6 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E6

Ranked by how often they cause this code
  1. 1Loose or damaged wiring harness connection
  2. 2Failed left side touch control module
  3. 3Moisture or contamination on the touch panel
  4. 4Corroded or oxidized connector terminals
  5. 5Main power control board fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E6

What does E6 mean on a Electrolux cooktop?
E6 indicates that the left rear zone key sensor on the touch control panel has been detected as defective. The cooktop's control system monitors the capacitive sensors on the touch panel, and when the left rear zone sensor fails to respond correctly, E6 is triggered. This fault is associated with the left side cook zones touch control module and its connection to the main power control board.
Is it safe to use my Electrolux cooktop while it shows E6?
You should avoid using the cooktop while the E6 error is active. The left rear zone sensor is reported as defective, which means the cooktop may not respond correctly to touch inputs for that zone, potentially leading to uncontrolled heating or the inability to turn a burner off reliably. Discontinue use until the fault has been diagnosed and repaired.
How much does it cost to repair an E6 error on an Electrolux cooktop?
Repair costs vary depending on whether the issue is a wiring connection or a failed touch control module. If only a connector needs to be reseated or cleaned, costs may be limited to a service call fee, typically in the range of $75 to $150. If the left side touch control module requires replacement, parts and labor combined can range from $200 to $450 or more depending on the specific model and local labor rates.
Can I fix the E6 error myself?
A knowledgeable DIYer can start by unplugging the cooktop, accessing the control panel area, and inspecting the wiring harness and connectors between the left side touch control and the main board for obvious damage or loose connections. If the wiring appears sound, replacing the left side cook zones touch control module is the next step, but this requires disassembly of the cooktop and working with electrical components. If you are not comfortable with this level of repair, a qualified technician is recommended.
Will resetting the cooktop clear the E6 error?
A power reset by unplugging the cooktop or switching off the circuit breaker for several minutes may temporarily clear the E6 code, but it will return if the underlying fault is not corrected. The error is tied to a hardware issue with the left rear zone key sensor or its wiring, so a reset alone does not constitute a repair.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass