mypros+
Error code reference

Electrolux Cooktop Error Code 19

RF zone control or On/Off key sensor defective.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 19 error code actually means

Error code 19 means your Electrolux cooktop has detected a problem with one of the touch control sensors, specifically the zone selector or the power button area on the right side of the control panel. The cooktop has stopped normal operation to prevent any unsafe behavior. A technician will need to check the wiring and possibly replace the right-side touch control panel to fix this.

Diagnostic procedure

The full 19 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Test cables and connections. If they are good, replace right side Touch Control Board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 19 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 19

Ranked by how often they cause this code
  1. 1Loose or damaged cable connections
  2. 2Moisture or liquid intrusion on control board
  3. 3Failed RF zone sensor on Touch Control Board
  4. 4Defective On/Off key sensor
  5. 5Heat-damaged wiring harness

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 19

What does 19 mean on a Electrolux cooktop?
Error code 19 indicates that the cooktop has detected a fault in the RF zone control sensor or the On/Off key sensor located on the right side touch control board. The control system monitors these sensors continuously and shuts down or restricts operation when it receives an abnormal or absent signal. The fault points specifically to the right side of the control panel, either the sensor itself or the wiring connecting it to the main board.
Is it safe to use my Electrolux cooktop while error code 19 is displayed?
It is not recommended to continue using the cooktop while error code 19 is active. The fault indicates that a key control sensor is not functioning correctly, which means the cooktop may not respond predictably to touch inputs, including attempts to turn it off. Discontinue use until the fault is diagnosed and resolved.
How much does it cost to repair error code 19 on an Electrolux cooktop?
Repair costs vary depending on whether the issue is limited to a wiring connection or requires a new right side Touch Control Board. If only a connection repair is needed, labor costs may range from around $75 to $150. If the Touch Control Board requires replacement, parts and labor combined can range from $150 to $350 or more depending on the specific model and local service rates.
Can I fix error code 19 myself on my Electrolux cooktop?
A knowledgeable DIYer can start by inspecting the cable connections and wiring harness between the touch control board and the main controller, as a loose or reseatable connection may resolve the fault without any parts. If connections are secure and undamaged, the right side Touch Control Board will need to be replaced, which requires disassembling the cooktop and working near electrical components. If you are not comfortable with appliance disassembly or electrical work, a qualified technician should perform the repair.
Will resetting my Electrolux cooktop clear error code 19?
A power reset by switching off the circuit breaker for 60 seconds may temporarily clear the display, but error code 19 will return if the underlying hardware fault is still present. The code is generated by a detected component or wiring failure, not a software glitch, so a permanent fix requires physical inspection and likely parts replacement.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass