mypros+
Error code reference

Electrolux Cooktop Error Code E07

Error code displayed as E on cooking zone displays and 07 on main control 2-digit display, indicating a control fault.

Electrolux codesElectrolux cooktop codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E07 error code actually means

Your Electrolux cooktop is showing a control system fault, meaning the main control board and the cooking zone controls are not communicating or functioning correctly. The simplest first step is to unplug or switch off the power to the cooktop, wait a moment, and restore power to see if the issue clears on its own. If the error comes back after resetting, the cooktop will need a closer inspection by a technician.

Diagnostic procedure

The full E07 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Disconnect the electrical supply and reconnect it to reset the main controls. If the fault recurs, note the error number and disconnect the electrical supply.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E07 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E07

Ranked by how often they cause this code
  1. 1Transient power disturbance
  2. 2Loose or damaged wiring harness connection
  3. 3Faulty main control board
  4. 4Faulty cooking zone control module
  5. 5Intermittent short or open circuit in control wiring

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E07

What does E07 mean on a Electrolux cooktop?
E07 indicates a control fault in the cooktop's control system. The code appears in a split format, with "E" showing on the cooking zone displays and "07" on the main 2-digit control display. It means the main control board has detected an error in the control circuitry or communication between the zone controls and the central controller. The cooktop will not operate normally until the fault is resolved.
Is it safe to use my Electrolux cooktop while it is showing E07?
No, you should not continue using the cooktop while E07 is active. A control fault means the control system is not functioning reliably, which can result in unpredictable behavior from the cooking zones. Disconnect the power supply and leave the cooktop off until the fault has been diagnosed and corrected.
Can I diagnose the E07 error myself, or do I need a technician?
A homeowner can safely attempt the initial power reset step without any tools or technical knowledge. However, if the error persists after resetting, further diagnosis involves inspecting internal wiring connections and potentially testing control boards, which requires disassembling the cooktop and working with electrical components. At that stage, a qualified appliance repair technician is strongly recommended.
Will resetting the power clear the E07 error?
A power reset is always the first step and will clear the fault if it was caused by a temporary electrical disturbance such as a surge or power fluctuation. Disconnect the electrical supply completely, wait at least 30 seconds, and then restore power. If the E07 code returns after the reset, the fault is persistent and requires hands-on diagnosis of the wiring and control boards.
How much does it cost to repair an E07 error on an Electrolux cooktop?
Repair costs vary depending on the root cause. If the fault is resolved by a power reset, there is no parts cost, though a service call fee may apply if a technician is involved. If the main control board requires replacement, parts and labor combined can range from $150 to $450 or more depending on the specific model and local labor rates. Zone control module replacements are generally less expensive.

Related Electrolux cooktop error codes

All Electrolux cooktop codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass