mypros+
Error code reference

Electrolux Cooktop Error Code E074

Internal generator error, communication, Induction Housing Assembly / Right side cooking zones.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E074 error code actually means

Your Electrolux induction cooktop has detected a communication problem between two internal circuit boards that control the right-side burners. As a result, the right-side cooking zones have been shut down to prevent any unsafe operation. A technician will need to inspect the internal wiring and circuit boards to find and fix the cause.

Diagnostic procedure

The full E074 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check cable between Filter Circuit Board connector X13 and Right Side Generator Circuit Board connector X10.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E074 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E074

Ranked by how often they cause this code
  1. 1Loose or disconnected cable connector
  2. 2Damaged or broken communication cable
  3. 3Corroded or contaminated connector contacts
  4. 4Failed Right Side Generator Circuit Board
  5. 5Failed Filter Circuit Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E074

What does E074 mean on a Electrolux cooktop?
E074 indicates an internal generator communication error affecting the right-side cooking zones. The cooktop has lost communication between the Filter Circuit Board and the Right Side Generator Circuit Board, which are connected via a cable running from connector X13 to connector X10. The right-side burners will be inoperable until this fault is resolved.
Is it safe to keep using my cooktop with an E074 error?
The right-side cooking zones will be disabled while E074 is active, so those burners cannot be used. The cooktop shuts them down specifically to prevent unsafe operation under a communication fault condition. You should not attempt to bypass this error, and the unit should be inspected and repaired before relying on the right-side zones again.
Will resetting my Electrolux cooktop clear the E074 error?
Resetting the cooktop by cutting power at the breaker for several minutes may temporarily clear the error display, but E074 will return if the underlying communication fault between the Filter Circuit Board and the Right Side Generator Circuit Board has not been corrected. A reset is not a repair, and the right-side zones will likely fault again quickly without addressing the root cause.
Can I fix the E074 error myself?
A knowledgeable DIYer can start by inspecting the cable and connectors between Filter Circuit Board connector X13 and Right Side Generator Circuit Board connector X10, as a loose or damaged connection is the most common cause. However, accessing these internal components requires disassembling the cooktop, and if a circuit board has failed, professional repair is strongly recommended. Working inside an induction cooktop involves high-voltage components and should only be done with the unit fully unplugged.
How much does it cost to repair an E074 error on an Electrolux cooktop?
If the fix is simply re-seating a loose connector, costs are minimal and limited to a service call fee, which typically ranges from $75 to $150. If the communication cable needs replacement, parts and labor combined generally fall in the $100 to $250 range. A failed Generator Circuit Board or Filter Circuit Board can push repair costs to $200 to $500 or more depending on parts pricing and labor rates in your area.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass