mypros+
Error code reference

Electrolux Cooktop Error Code E51

Left Front element temperature sensor break.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E51 error code actually means

Your Electrolux cooktop has detected a problem with the temperature sensor on the left front burner. The sensor that monitors heat for that burner has stopped sending a signal to the control board, so the cooktop shut that burner off as a safety measure. This will need to be diagnosed and repaired before that burner can be used again.

Diagnostic procedure

The full E51 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Verify element temperature sensor is correctly connected to the generator circuit board. Replace element if temperature sensor resistor value is not approximately 1000 ohms (blue wires) at room temperature. Replace associated generator circuit board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E51 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E51

Ranked by how often they cause this code
  1. 1Failed element temperature sensor
  2. 2Disconnected sensor connector at the generator board
  3. 3Broken or damaged sensor wiring
  4. 4Faulty generator circuit board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E51

What does E51 mean on a Electrolux cooktop?
E51 indicates a break or open-circuit condition in the temperature sensor for the left front induction element. The generator circuit board monitors a thermistor in the element that should read approximately 1000 ohms at room temperature. When that signal is lost, the board disables the left front burner and displays E51 as a safety response.
Will resetting the cooktop clear the E51 error?
A power reset, such as turning off the circuit breaker for 30 seconds, may temporarily clear the display, but E51 will return as soon as the cooktop attempts to use the left front element if the underlying fault is still present. The error indicates a hardware fault in the sensor circuit that must be physically corrected before the burner will operate normally.
How much does it cost to repair an E51 error on an Electrolux cooktop?
Repair costs vary depending on which component has failed. If the connector simply needs reseating, there may be no parts cost at all, though a service call typically runs between $75 and $150. Replacing the left front element assembly generally costs between $150 and $400 in parts plus labor. A generator circuit board replacement can range from $200 to $500 or more in parts depending on the model, with additional labor costs on top.
Can I fix the E51 error myself?
A knowledgeable DIYer can start by checking whether the blue sensor wire connector is properly seated at the generator circuit board, which requires no parts and may clear the fault. Testing sensor resistance with a multimeter is also within reach for those comfortable with basic electrical diagnosis. However, if the element or generator board needs replacement, those repairs involve working inside a high-voltage appliance and are best handled by a qualified technician.
Is it safe to use the cooktop with an E51 error showing?
The cooktop disables the left front element when E51 is active, so that specific burner will not generate heat. Other elements may continue to function, but operating the appliance with an active fault is generally not recommended. The temperature sensor is a key safety component, and the fault should be resolved promptly to avoid any risk of uncontrolled heating if the error is intermittent.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass