Skip to main content
Error code reference
Electrolux Washer Error Codes
232 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
0000Flashing display indicating the machine has detected an imbalance; the built-in imbalance…11Fill time too long.13Water leak in tub or in pressure sensor.21Water not pumping out fast enough.23Drain triac error.24Drain triac error sensing.31Electronic pressure switch error.32Pressure sensor calibration problem.35Pressure sensor indicates water overfill.38Air trap clogged.41Control board thinks the door switch is open.42Door lock device failure.43Door lock triac failure.44Door closed sensing failure.45Line door sensing failure.55Motor under speed (not available on 300 series, select models only).57High current on inverter (motor control).58High current on motor phase.59No spin signal for 3 seconds.5AHigh temperature on control due to overload (motor control).5BMotor control under voltage.5CHigh voltage experienced by motor control board.5DCommunication problem with motor control (message).5ECommunication problem from motor control (communication failure).5FMC (motor control) is continuously resetting.62Wash temperature too high.66Heater relay problem (on select models).68Current leakage to ground on heater or wiring (on select models).69Heater open (on select models).6AHeater relay sensing problem (on select models).71Drum water NTC failure (tub heater) (on select models).74Wash temperature does not increase.83Wrong selector reading.84Recirculation pump triac sensing failure which stops the cycle (on select models).85Recirculation pump triac alarm which stops the cycle (on select models).86Incorrect UI selection table.87User interface micro-controller fault.88Concentrated wash pump triac alarm (on select models).91User interface protocol incongruence error.92Communication error UI to main board (incompatible configuration).93Console or main board control problem (incompatible machine configuration).94Main board control problem (incompatible cycle configuration).97Console or main board control problem (incompatible cycle configuration).98Incompatible motor control/main board.9CUser Interface configuration problem.9ETouch sensor on user interface not responding.C1Flow meter is running when no valves are driven.ddoDrawer reed switch is not closed (dispenser drawer open).drDoor switch is not closed.E00No alarm stored in memory.E10No water filling-water tap closed, valve does not open/interruption, or valve flow rate…E11Difficulty filling water during wash cycleE12Water fill difficulty during drying cycleE13Water leakage detected-drain hose incorrectly positioned, mains pressure insufficient…E14Reed switch fault-dispenser drawer reed switch circuit interrupted.E20No draining-pump blocked/not working, pump interrupted, reduced pump output rate…E21Difficulties in drainingE22Difficulty in water fill during drying or drying condenser clogged (anti-boiling pressure…E23Drain pump triac failureE24Malfunction in sensing circuit on triac for drain pump (wrong input voltage to…E25Aqua control sensing failureE30Fault in the analogue (electronic) pressure switch detected by MWM 1.5 control system.E31Electronic pressure switch failureE32Electronic pressure switch improperly calibratedE33Inconsistency between anti-boiling and 1st level pressure switch contact closureE34Incongruency between level of electronic pressure switch and level of anti-boiling…E35Safety level (pressure sensor)-level has to be 300mm for a time of more than 15 sec…E36Sensing circuit of anti-boiling pressure switch 1 on the electronic board is not working…E37No pressure differences detected-airtrap blocked, or antiboil 2 sensing failure (input…E38Pressure chamber blockedE39Overflow pressure switch HV sensing circuit defectiveE3AHeating element relay sensing faultyE40User-displayed code for door open or door lock problems (covers E41, E42, E43).E41Door open detectedE42Problems with door lock; wiring defective, door safety interlock defective, electrical…E43Faulty TRIAC supplying power to door delay system; wiring defective, door safety…E44Door closed sensing failureE45Door lock delay triac detection circuit defectiveE46Board communications problem.E47Board thinks the door PTC circuit is open in spin.E48Board thinks the door PTC circuit is closed.E49Door incongruence between door line and door sense.E50Motor triac short circuit (EWM2100)-motor cable short circuit.E51Motor supply triac short-circuitE52No signal from motor tachometer generatorE53Motor triac detection circuit defectiveE54Motor direction relay failureE55Under speed-wiring problem, motor defective, or motor control board defective.E56Motor triac sensing failure-input voltage always 0V or 5V.E57FCV current trip failureE58High current on motor phase exceeding 4.5 A due to motor malfunction, heavy laundry load…E59No signal from tachometric generator for 3 seconds due to faulty wiring on inverter for…E5AOverheating on heat dissipater for inverterE5BMotor control under voltage-motor control board defective or voltage out of range.E5CInput voltage is too high; voltage out of range, defective inverter board, or defective…E5DFCV unknown message failureE5EFCV-motherboard communication failureE5FMotor control is continuously resetting-main circuit board defective, motor control board…E5HInput voltage is lower than 175 V; defective inverter board or wiring problem.E60Insufficient heating-maximum heating time expired, heating element defect, NTC defective.E61Insufficient heating during wash cycleE62Overheating during washing (temperature higher than 88°C for more than 5 min)E63Insufficient heating measured by the main board during drying cycle.E64Overheating during drying cycle-more than 180°C.E66Heating element defect-incongruence between antiboil 1/2 and relay, connection heating…E67Input voltage on microprocessor incorrect.E68Ground current leakageE69Heating element openedE6AHeater relay sensing failureE6HHeating element power relay faulty; earth-leakage between heating element and earth…E70NTC defective-NTC interruption or short circuit detected (cut or short-circuit on…E71NTC probe for wash cycle faulty (short-circuited or open); drum water NTC defective…E72Fault in NTC sensor on drying condenser (voltage out of range = short-circuit or open…E73Fault in NTC sensor on drying duct (voltage out of range = short-circuit or open circuit)E74NTC sensor for wash cycle improperly positionedE75Drying capillary NTC failureE76NTC temperature for the cold water valve over the limitsE80Wrong selector reset position detection.E82Error in reset position of selectorE83Error in reading selector positionE84Recirculation pump defectiveE85Defective sensing circuit on triac for recirculation pumpE86Selector configuration table errorE87User interface microcontroller faultE88Recirculation pump failure.E90User-displayed code for communication or configuration errors (covers E91, E93).E91Communication error between main control board and display board; UI board defective…E92Inconsistency in communication between main board and display board (versions not…E93Incorrect machine configurationE94Incorrect washing cycle configurationE95Communication error between microprocessor and EEPROME96Incompatibility between hardware version and configurationE97Incompatibility between programmer and cycle configurationE98Communication error between main control board and inverter board; main circuit board…E99Connection between loudspeaker and In/Output electronic defective.E9AFirmware between loudspeaker and In/Output electronic not ok.E9bCommunication error between micro-processor and FLASH memory.E9CUser interface configuration problem-main circuit board defective, motor control board…E9dClock faulty.E9EKey stuck or contaminated-user interface board defective or control panel defective.E9FCommunication error between PCB and remote devicesE9HCommunication error between micro-processor and FLASH memory.EA0DSP defect-wiring or drive belt cut, DSP or electronic defective.EA1Drum positioning system (DSP) defective (top-loading machines)EA2Power supply voltage too high.EA3DPS unable to lock motor pulley.EA4DPS defect-triac for DPS defect.EA5Main voltage sensing failure.EA6Drum door defective (top-loading machines)EAELine safe relay sensing failure.EB0Power supply frequency out of limits-wrong or disturbed power supply line.EB1Power supply frequency of appliance incorrectEB2Supply voltage too highEB3Supply voltage too lowEBEInconsistency between safety relay and sensing circuitEBFSensing circuit on safety system defectiveEC0Inlet valve blocked-no signal from flow meter with electro valves switched on.EC1Electronically controlled valve blocked with operating flowmeter; wiring defective, water…EC2Data transfer error between weight sensor and main control board; wiring defective…EC3Problems with weight sensor (no signal or outside the limits); wiring defective, weight…EC4Current sensor alarmEC8TY5 triac failureEC9TY5 triac sensing failureECADetergent dispenser water softener board communication alarmECCWater softener assembly failureECDWater softener pump failureECHDetergent dispenser water softener board faultED1Data communication error between WD board and PCBED2Drying heating element relay 1 faultyED3Drying heating element relay 2 faultyED4Relay which commutates power between washing heating element and drying (in the WD board)…ED5WD heating element2 relay sensing failureED6No communication between PCB and display board (INPUT)ED7WD thermostat openedED8WD fan motor tachometer absentED9WD fan motor driving circuit failureEDAWD power supply alarmEDCWDM heating element openedEDDWDM ground current leakage alarmEDHWDM microcontroller faultEE1Fan current trip failureEE2Fan over current failureEE4Fan not following alarmEE5Fan under voltage alarmEE6Fan over voltage alarmEE7Fan plug not connected alarmEE8Fan NTC wrong temperature failureEEBCooler fan failureEECCompressor failureEF0Aqua control sensor active (water leakages) or detergent overdosing or unbalanced laundry…EF1Drain filter blocked-warning that appears only at the end of the cycle indicating long…EF2Overdosing of detergent (too much foam during drain phases)-excessive detergent dosing…EF3Aqua Control system activated-leakage in the machine, drain pump cable defective, drain…EF4Water fill pressure too low, no signal from flow meter and solenoid valve is openEF5Load unbalancedEF6Safety resetEF7Dry filter alarmEF8Salt missing warningEF9Hot valve warning-hot and cold hoses reversed.EH0Low mains voltage or irregular mains frequency out of standard working range.EH1Power supply frequency out of limitsEH2Power supply voltage too highEH3Supply voltage too low-main circuit board defective or fluctuation in input.EH4Zero Watt relay alarmEHCLine WD relay failureEHDHeater WD relay sensing failureEHEInconsistency between FCV relay and safety sensing circuit; main circuit board defective…EHFSafety system sensing circuit faultF 01An internal fault in the control.F 02A water temperature problem.F 03Water level problem caused by either no incoming water or the drain pump not working.F 04The washer is not advancing through its increments.F 05A problem with the key pad.F1Overflow condition detected by sensor; on some models an inter valve has opened; machines…F2Wash motor fault caused by interruption in cables to the motor, a faulty motor capacitor…F3Draining fault indicating the machine has not succeeded in pumping out the water within 2…F4Water inlet fault indicating the machine does not reach the required water level within 5…F5Heating pause faultF6Temperature stop fault indicating the wash temperature is not reached within 80 minutes…F7Foaming detected after the main wash (this function is not provided on all machines).F8Door opening fault indicating a fault on the control card which must be replaced to…F9Hot valve warningH1/B1Frequency of power out of limits.H2/B2Supply voltage too high (incoming voltage).H3/B3Supply voltage too high (incoming voltage).HE/BEControl relay fault.HF/BFControl relay sense fault.L1Over fillingL2Door open faultL3Drainage faultL4Fault with water supplyL5Door opening fault
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Electrolux error codes
Common questions
How do I find the error code on my Electrolux Washer?
Most Electrolux washers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Electrolux washers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.