mypros+
Error code reference

Electrolux Washer Error Code E44

Door closed sensing failure

Electrolux codesElectrolux washer codes

Door closed sensing failure - door sensing not working properly, should give sinusoidal wave if closed or 2.5V if open.

First step from the service manual

Check door lock device, wiring or main board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E44.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E44 means on a Electrolux washer

Error code E44 on an Electrolux washer indicates a door closed sensing failure. The door lock assembly on this washer incorporates a sensor that communicates the door's status to the main control board using specific electrical signals. When the door is properly closed and locked, the sensor is designed to produce a sinusoidal (AC-type) wave signal. When the door is open, the sensor outputs a steady 2.5V DC signal. If neither of these expected signals is detected by the control board within the proper parameters, E44 is triggered and the washer will halt operation.

This error most commonly points to a fault within the door lock device itself, the wiring harness connecting the door lock to the main board, or a failure on the main board's input circuit that reads the door sensor signal. A damaged or worn door lock mechanism can cause the sensor inside to fail, producing no signal or an incorrect signal. Similarly, wiring issues such as a broken wire, corroded connector pin, or loose harness plug between the door lock and the control board can interrupt or distort the signal before it reaches the board.

Diagnosing E44 requires checking the door lock device for physical damage or continuity issues, inspecting the wiring harness for breaks or corrosion at connector points, and verifying the correct signals are present at the main board's input terminals. If the wiring and lock device test correctly, a faulty main board input circuit may be responsible. Systematic testing starting at the door lock and working toward the board is the most efficient diagnostic approach.

Source: manufacturer service documentation.

Common causes of E44

  1. 01

    Faulty door lock assembly

    Part replacement

    The door lock device contains the sensor responsible for generating the sinusoidal signal when closed or the 2.5V signal when open. Internal failure of this component is the most frequent cause of E44 and may require replacement of the entire door lock assembly.

  2. 02

    Damaged or disconnected wiring harness

    Wiring / connection

    The wiring between the door lock and the main board can develop breaks, shorts, or loose connector pins over time. Inspect the harness along its full length and check each connector for corrosion or poor seating.

  3. 03

    Corroded or loose connector pins

    Wiring / connection

    Connector pins at the door lock plug or at the main board header can corrode or back out, disrupting the signal. Cleaning contacts and reseating connectors sometimes resolves the error without replacing any parts.

  4. 04

    Worn or physically damaged door latch

    Part replacement

    If the door latch mechanism does not fully engage the lock assembly when the door is closed, the sensor inside may not activate properly, producing an incorrect or absent signal.

  5. 05

    Main control board input circuit failure

    Part replacement

    If the door lock device and all wiring test correctly, the circuit on the main board that reads the door sensor signal may have failed. This is the least common cause but requires board repair or replacement if confirmed.

See the test procedure for each cause

Frequently asked questions about E44

What does E44 mean on a Electrolux washer?
E44 indicates a door closed sensing failure on your Electrolux washer. The door lock sensor is expected to produce a sinusoidal wave signal when the door is closed, or a steady 2.5V signal when open. When neither correct signal is detected, the washer displays E44 and stops operation. The most likely causes are a faulty door lock device, a wiring problem, or a main board issue.
Can I fix E44 on my Electrolux washer myself?
Some E44 repairs are within reach for a DIYer with basic electrical knowledge. Start by checking that the door closes and latches fully, then inspect the wiring harness and connectors between the door lock and the control board for visible damage or loose pins. If the wiring looks intact, the door lock assembly itself is the next most likely component to replace. Main board replacement is more complex and may benefit from professional diagnosis.
Is it safe to use my Electrolux washer when E44 is showing?
No, you should not attempt to run the washer while E44 is active. The error means the machine cannot reliably confirm the door is secured, and operating it in this state could allow the door to open during a cycle, posing a water leak and injury risk. Resolve the underlying fault before resuming normal use.
Will resetting my Electrolux washer clear the E44 error?
A power reset by unplugging the washer for a few minutes may temporarily clear the display, but the error will return if the underlying hardware fault is not repaired. E44 is a sensor signal fault that requires diagnosing and fixing the door lock device, wiring, or main board to be permanently resolved.
How much does it cost to repair an E44 error on an Electrolux washer?
Repair costs vary depending on the faulty component. A replacement door lock assembly typically costs between $30 and $90 for the part alone. If professional labor is needed, total repair costs including parts and labor generally range from $100 to $250. Main board replacement is the most expensive scenario and can range from $200 to $400 or more depending on the model and labor rates in your area.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass