Model reference
Electrolux 599337005
Washer
1 document41 error codes15 service modes
Available documentation
Service Manual
- Ewm 2000 Elektronikus SzabÁlyzÓk (Zp) ÖSszefoglalÓja27 pg
MyPros+ Max
Diagnose your Electrolux 599337005.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (41)
CodeMeaning
E10User-displayed code for water filling problems (covers E11 and E12).E11Water filling problems during the wash phase.E12Water filling problems during the drying phase.E20User-displayed code for draining problems during wash phase (covers E21).E21Draining problems during the wash phase.E22Draining problems during drying or dryer condenser clogged.E31Analog (electronic) pressure switch circuit fault.E32Incorrect pressure switch calibration.E33Inconsistency between pressure switch level and anti-boiling switch level 1.E34Inconsistency between pressure switch level and anti-boiling switch level 2.E35Water level too high.E36Anti-boiling pressure switch 1 circuit faulty.E37Anti-boiling pressure switch 2 circuit faulty.E38Pressure chamber clogged.E40User-displayed code for door open or door lock problems (covers E41, E42, E43).E41Door open.E42Door lock problems.E43Door lock power supply TRIAC faulty.E44Door lock delay circuit faulty.E45Door lock delay TRIAC faulty.E51Motor power supply TRIAC short-circuited.E52No signal from the tachometer generator.E53Motor TRIAC sensing circuit faulty.E54Motor relay fault.E61Ineffective heating during wash.E62Overheating during wash.E63Ineffective heating during drying.E64Overheating during drying.E66Heating element power supply relay faulty.E71Wash NTC sensor faulty.View all 41 error codes
E72Dryer condenser NTC sensor faulty.E73Dryer duct NTC sensor faulty.E84Circulation pump sensing circuit faulty.E85Circulation pump faulty.E90User-displayed code for communication or configuration errors (covers E91, E93).E91Communication error between the main PCB and the user interface.E93Configuration error.E94Wash cycle incorrect configuration.EF0User-displayed LED code for drain filter clogged or excessive detergent (covers…EF1Drain filter clogged.EF2Excessive detergent dosage.
Service modes (15)
- Diagnostic mode - AEG with ON/OFF switch on program selector (Table 5)["Turn off the appliance and rotate the program selector to the OFF/RESET position.","Press buttons…
- Diagnostic mode - DELTA 3 / NEAT (Table 3)["Press the SKIP/RESET button to clear any previously selected program, then turn off the…
- Diagnostic mode - Full SMD with ON/OFF button (Table 1)["Turn off the appliance and rotate the program selector to the RESET position.","Press the…
- Diagnostic mode - Full SMD with ON/OFF switch on program selector (Table 2)["Turn off the appliance.","Press the Start/Pause button (8) together with another button, hold…
- Diagnostic mode - INPUT (Table 4)["Turn off the appliance.","Press the SPIN button (3) together with button 4, hold them pressed…
- PCB Configuration - AEG (Table 5)["Enter diagnostic mode first.","Rotate the program selector to the last position (24 or 21).","The…
- PCB Configuration - DELTA 3 / NEAT (Table 3)["Enter diagnostic mode first.","Press FABRICS (1) or TEMPERATURE (2) button until LED10 lights up
- PCB Configuration - Full SMD ON/OFF button (Table 1)["Enter diagnostic mode first.","Rotate the program selector one position counter-clockwise
- PCB Configuration - Full SMD ON/OFF switch on selector (Table 2)["Enter diagnostic mode first.","Rotate the program selector to the last position (24 or 12)
- PCB Configuration - INPUT (Table 4)["Enter diagnostic mode first.","Press FABRICS (1) or TEMPERATURE (2) button until LED14 lights up
- Read last alarm - AEG (Table 5)["Enter diagnostic mode first.","Rotate the program selector to the last position (11, 20, or 23)."]
- Read last alarm - DELTA 3 / NEAT (Table 3)["Enter diagnostic mode first.","Press the FABRICS or TEMPERATURE button together with button 4…
- Read last alarm - Full SMD ON/OFF button (Table 1)["Enter diagnostic mode first.","Rotate the program selector two positions counter-clockwise from…
- Read last alarm - Full SMD ON/OFF switch on selector (Table 2)["Enter diagnostic mode first.","Rotate the program selector to the last position (23 or 11)."]
- Read last alarm - INPUT (Table 4)["Enter diagnostic mode first.","Press FABRICS or TEMPERATURE button until LED11 lights up."]
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax