mypros+
Error code reference

Electrolux Washer Error Code E93

Incorrect machine configuration

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E93 error code actually means

Your Electrolux washer has detected that its main computer board is not set up correctly for your specific machine, so it has shut down completely to prevent any damage. All the lights on the panel will be on at the same time, and the washer will not start any cycles. This is a serious internal electronics issue that requires a technician to reprogram or replace the control board.

Diagnostic procedure

The full E93 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace or reprogram main board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E93 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E93

Ranked by how often they cause this code
  1. 1Incorrectly programmed replacement board
  2. 2Corrupted board firmware or configuration memory
  3. 3Failed or interrupted firmware update
  4. 4Defective main control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E93

What does E93 mean on a Electrolux washer?
E93 indicates an incorrect machine configuration fault, meaning the main control board's programming does not match the expected setup for the washer. When this error is active, all LEDs on the panel light up simultaneously and all wash operations are blocked. The built-in diagnostic mode is also inaccessible while E93 is present. The fault points directly to the main board requiring reprogramming or replacement.
Will resetting my Electrolux washer clear the E93 error?
No, a power cycle or reset will not clear E93. The fault is stored in the non-volatile configuration memory of the main board, meaning it persists regardless of whether power is removed. Because the error reflects a fundamental programming mismatch rather than a temporary sensor or communication issue, it will return immediately after every restart until the board is reprogrammed or replaced.
How much does it cost to fix an E93 error on an Electrolux washer?
Repair costs depend on whether the board needs reprogramming or full replacement. Main control board replacement for Electrolux washers typically ranges from $150 to $400 or more for the part alone, depending on the model. Adding professional labor costs for diagnosis and installation, total repair bills commonly fall in the range of $250 to $550. Reprogramming an existing board, if available in your area, may cost less than full replacement.
Can I fix E93 on my Electrolux washer myself?
Resolving E93 requires either reprogramming the main board with the correct configuration data or replacing the board with a properly matched unit. Reprogramming typically requires specialized software and tools that are not available to most homeowners. Board replacement is a task some experienced DIYers can perform, but the replacement board must be correctly programmed for your specific model, which usually requires a qualified technician.
Is it safe to use my Electrolux washer when E93 is showing?
The washer automatically blocks all operations when E93 is active, so it cannot be used in this state. Attempting to force operation is not possible through normal controls. The machine should remain unused until the main board issue is resolved, as operating with a misconfigured board could cause unpredictable behavior if the lockout were somehow bypassed.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass