mypros+
Model reference

Frigidaire 2010

Air Conditioner

3 documents62 error codes16 service modes

Available documentation

Service Manual

  • All about the Service of Room Air Conditioner193 pg
    Covers this model
  • Technical Service Manual 2010 Room Air Conditioner REVISION A253 pg
    Covers this model

Other

  • 2010 2 service la artcool gallery system 3828a20926c 20120509091718 pdf76 pg
    Covers this model
MyPros+ Max

Diagnose your Frigidaire 2010.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (62)

CodeMeaning
ASAmbient thermistor sensor located in front of the evaporator has failed.CSCondenser thermostat sensor has failed (heat pump models only); displays for 1…E00No failure code experienced; no error stored in memory.E11Fill time too longE13Water leak detectedE21Drain time too longE31Contact Sensor frequency too high.E32Contact Sensor frequency too low.E35Water level pressure sensor errorE38Pressure sensor difference errorE41Door lock errorE42Door unlock errorE43Control board errorE44Door open errorE45Door lock relay error on main control board.E51Motor Relay failureE52Motor control signal errorE53Motor Centripetal Switch Failure.E54Motor control overcurrent errorE57Motor control high current errorE58Motor control high current error on phase.E59Motor control no tachometer signalE5AMotor control heatsink overtemperature on speed control board.E5BMotor control high voltage on DC bus of speed control board.E5CMotor control low voltage on DC bus of speed control board.E5DMotor control communication errorE5EMotor control communication error between main board and motor control.E5FMotor control errorE61Heater error during washE62Heater overtemperature
View all 62 error codes
E63Heater to Earth GroundE64Heater Open CircuitE65High Limit Thermostat trip count too highE66Heater relay error on main control board.E67Heaters Sensing Failure due to defective Electronic Control Board.E68Heater current leakE69Heater NTC breakE6AHeater NTC shortE6CDispenser NTC breakE6DDispenser NTC shortE71Outlet Control Thermistor open circuit.E72Outlet Control Thermistor short circuit.E73Inlet Control Thermistor open circuit.E74Motor Relay failureE91Communication error between user interface (UI) and main board (MB).E92Communication errorE93Main board configuration error.E94Cycle configuration error on main board.E95Communication error between main board and motor control during startup.E97Program mismatchEA1Main Supply Frequency out of RangeEA2Voltage too highEA3Voltage too lowEA4Improper home wiringEA5Main V Sensing failure due to defective Electronic Control Board.EABCommunication error between main board and user interfaceEF1Vent BlockedEF3Max Timeout TimerEF8Key StuckESEvaporator thermistor sensor has failed.HSHeat thermistor sensor has failed (heat capable models only).OSOutdoor ambient thermostat sensor has failed (heat pump models only); displays…

Service modes (16)

  • Clear Stored Error Codes["1
  • clear_error_codes["Press the CANCEL button to enter standby mode and enable diagnostic entry.","Within 10 seconds…
  • Demo Mode (IQ Touch)["1
  • Demo Mode (Wave Touch)["1
  • demo_mode_iq_touch["Turn the cycle selector knob to TIME DRY cycle, press the START button then the CANCEL…
  • demo_mode_wave_touch["Turn the cycle selector knob to TIME DRY cycle, press the START button then the CANCEL…
  • diagnostic["Press the CANCEL button to enter standby mode and enable diagnostic entry.","Within 10 seconds…
  • Diagnostic Mode (Error Code Reading)["1
  • Diagnostic Test Mode (Component Test)["1. Press the CANCEL button to enter standby mode.","2. Within 10 seconds after pressing CANCEL…
  • install_cycle_iq_touch["Empty dryer drum and close door.","After plugging in the dryer the first time, wake up the dryer…
  • install_cycle_wave_touch["After plugging in the dryer the first time, wake up the dryer by pressing any button and follow…
  • Installation Cycle (IQ Touch)["1
  • Installation Cycle (Wave Touch)["1. After plugging in the washer the first time, wake up the washer by pressing any button and…
  • read_error_codes["Wake the dryer up by pressing any button (except the cancel button).","Press and hold the CANCEL…
  • Reset (IQ Touch)["1
  • Reset (Wave Touch)["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Frigidaire air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax