mypros+
Error code reference

Electrolux Washer Error Code EE1

Fan current trip failure

Electrolux codesElectrolux washer codes

Fan current trip failure - hardware problem on power module causing current immediately above 2.5A.

First step from the service manual

Check fan wiring or fan control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EE1.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EE1 means on a Electrolux washer

The EE1 error code on an Electrolux washer indicates a fan current trip failure rooted in a hardware problem on the power module. Specifically, the fault is triggered when the fan circuit draws current immediately above 2.5 amps, which causes the power module to trip as a protective response. This is not a soft or intermittent fault but a hard hardware-level detection, meaning the module itself is registering an overcurrent condition at the fan circuit the moment power is applied or the fan is commanded to run.

The fan referenced here is typically the cooling fan for the motor drive electronics or power module assembly. When current spikes above the 2.5A threshold, the power module interprets this as a potentially damaging condition and shuts down the fan circuit to protect downstream components. This can stem from a mechanical restriction in the fan itself, a short circuit in the fan wiring harness, or a failed fan motor that is drawing excessive current due to worn bearings or shorted windings.

The first diagnostic step is to inspect the fan wiring and the fan control board. Look for chafed, pinched, or shorted wiring between the fan motor and the power module. Check connector pins for corrosion or damage. If wiring checks out, the fan motor should be tested for proper resistance and free mechanical rotation. If the fan and wiring are intact, the power module itself may have an internal hardware fault and require replacement.

Source: manufacturer service documentation.

Common causes of EE1

  1. 01

    Faulty fan motor

    Part replacement

    A fan motor with worn bearings or shorted windings will draw current above the 2.5A trip threshold immediately on startup. Spin the fan blade by hand to check for stiffness or binding, and test motor winding resistance.

  2. 02

    Short circuit in fan wiring harness

    Part replacement

    Chafed, pinched, or melted wiring between the fan motor and the power module can create a short that spikes current above the trip point. Inspect the full length of the harness for damage and check connector pins for corrosion or contact bridging.

  3. 03

    Failed fan control board

    Part replacement

    The fan control board may have an internal component failure that causes an overcurrent condition even if the fan motor itself is functional. If the fan and wiring test good, the control board should be evaluated as the next suspect.

  4. 04

    Failed power module with internal hardware fault

    Part replacement

    Because EE1 is classified as a hardware problem on the power module, the module itself may have developed an internal fault that falsely trips the current detection circuit. This is typically diagnosed after ruling out the fan and wiring.

  5. 05

    Obstruction blocking fan rotation

    Wiring / connection

    Debris or foreign material lodged against the fan blade can prevent free rotation, causing the motor to stall and draw excessive current. Remove the panel to access the fan and visually inspect for any physical blockage.

See the test procedure for each cause

Frequently asked questions about EE1

What does EE1 mean on a Electrolux washer?
EE1 indicates a fan current trip failure caused by a hardware problem on the power module. The fault is triggered when the fan circuit draws current immediately above 2.5 amps. The power module shuts down the fan circuit as a protective response. This fault requires diagnosis of the fan, its wiring, and potentially the power module or fan control board.
Can I fix the EE1 error on my Electrolux washer myself?
Some causes, such as a physical obstruction blocking the fan blade, can be cleared without specialized tools or replacement parts. However, diagnosing a shorted wiring harness, failed fan motor, or faulty control board requires multimeter testing and comfort working around electrical components. If you are not experienced with appliance electrical repair, a qualified technician should handle this fault.
Is it safe to use my Electrolux washer with an EE1 error?
You should not continue running the washer while the EE1 fault is active. The error indicates the power module has detected an overcurrent condition and tripped as a safety measure. Running the machine without resolving the underlying cause risks further damage to the power module, control board, or wiring.
How much does it cost to repair an EE1 error on an Electrolux washer?
Repair costs vary depending on the failed component. Fan motor replacement typically runs in the range of $80 to $180 including parts and labor. A power module or fan control board replacement can range from $150 to $350 or more depending on the part cost and labor rates in your area. Wiring harness repairs are generally on the lower end of the cost range if no boards need replacement.
Will resetting my Electrolux washer clear the EE1 error code?
A reset may temporarily clear the EE1 code from the display, but the fault will return as soon as the fan circuit is powered and the overcurrent condition is still present. Because EE1 reflects a hardware-level detection, the underlying cause must be repaired before the code will stay clear. Repeatedly resetting without repair will not resolve the problem.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass