mypros+
Error code reference

Electrolux Washer Error Code 0000

Flashing display indicating the machine has detected an imbalance; the built-in imbalance sensor has reduced…

Electrolux codesElectrolux washer codes

Flashing display indicating the machine has detected an imbalance; the built-in imbalance sensor has reduced spin speed or locked out the spin completely.

First step from the service manual

Switch off the main switch and turn it on again, open the door and redistribute the wash, close the door and start the Spin program.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0000.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0000 means on a Electrolux washer

The Electrolux washer error code 0000 is indicated by a flashing display and signals that the machine's built-in imbalance detection system has triggered a protective response during the spin cycle. The imbalance sensor continuously monitors the drum load distribution as spin speed increases. When it detects an uneven load, it either reduces the spin speed to a safer level or locks out the spin cycle entirely to prevent excessive vibration, mechanical stress, and potential damage to the drum bearings, suspension components, and cabinet structure.

This condition is not a component failure in most cases. It is a software-driven safety response designed to protect the machine and surrounding surfaces. The trigger is typically a laundry load that has shifted, clumped, or bundled unevenly during the wash cycle. Heavy single items such as towels, jeans, or bedding are particularly prone to balling up on one side of the drum, creating a rotational imbalance that the sensor detects almost immediately when spin ramp-up begins.

Because the imbalance response can range from a reduced spin speed to a complete spin lockout, the severity of the symptom depends on how far off-balance the load is detected to be. The machine may attempt to redistribute the load on its own through low-speed tumbling before escalating to a lockout. If automatic redistribution fails, the flashing display activates and user intervention is required to manually redistribute the laundry before the spin program can proceed normally.

Source: manufacturer service documentation.

Common causes of 0000

  1. 01

    Uneven laundry distribution

    Wiring / connection

    Clothes have clumped or bundled to one side of the drum during the wash cycle. This is the most frequent trigger and is identified by visually inspecting the drum and finding laundry piled on one side.

  2. 02

    Single large or heavy item

    Wiring / connection

    Washing one large item such as a comforter, heavy towel, or pair of jeans by itself causes the drum to become one-sided as the item absorbs water and settles. Adding a few smaller items to balance the load typically resolves this.

  3. 03

    Overloaded drum

    Wiring / connection

    Packing too many items into the drum restricts free tumbling during the wash, making it difficult for the machine to redistribute the load. The drum should not be filled beyond roughly three-quarters of its capacity.

  4. 04

    Machine not level on the floor

    Wiring / connection

    If the washer is sitting on an uneven surface or the adjustable feet are not properly set, even a reasonably balanced load can trigger the imbalance sensor. Check that all four feet are making firm contact with the floor and that the machine does not rock.

  5. 05

    Worn or damaged suspension components

    Part replacement

    If the error occurs repeatedly even with small, well-distributed loads, worn suspension rods, dampers, or drum bearings may be causing excessive drum movement that the sensor interprets as imbalance. This scenario requires inspection and potential replacement of suspension parts.

See the test procedure for each cause

Frequently asked questions about 0000

What does 0000 mean on a Electrolux washer?
The 0000 code on an Electrolux washer appears as a flashing display and means the built-in imbalance sensor has detected an uneven load in the drum during the spin cycle. In response, the machine reduces spin speed or stops the spin completely to prevent vibration damage. It is a protective feature, not a component failure. Redistributing the laundry and restarting the spin program usually clears it.
How do I fix the 0000 imbalance error on my Electrolux washer?
Turn the machine off using the main switch, then turn it back on. Open the door and manually redistribute the laundry so the load is spread evenly around the drum. Close the door and start the Spin program again. If the error returns, remove some items or add a few smaller items to help balance a single heavy piece.
Will resetting my Electrolux washer clear the 0000 error?
Turning the main switch off and back on resets the control and clears the active error display, but if the underlying load imbalance is not corrected, the sensor will detect it again as soon as spin speed ramps up and the code will return. The reset must be combined with manually redistributing the laundry to actually resolve the issue.
Is it safe to keep using my Electrolux washer when the 0000 code appears?
The machine is designed to protect itself by reducing or stopping the spin when this code appears, so immediate mechanical damage is unlikely. However, repeatedly forcing spin cycles with an unbalanced load, or ignoring the code if it appears even with balanced loads, can accelerate wear on drum bearings and suspension components over time. Address the imbalance before continuing use.
How much will it cost to repair the 0000 imbalance error if it is caused by a mechanical problem?
If the error is caused by laundry distribution, there is no repair cost involved. If the repeated imbalance errors point to worn suspension rods, dampers, or drum bearings, repair costs can range from around 75 dollars to over 300 dollars depending on which components need replacement and whether you hire a technician or perform the repair yourself. Getting a diagnostic inspection first helps identify the exact cause before committing to parts.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass