mypros+
Error code reference

Electrolux Washer Error Code E14

Reed switch fault

Electrolux codesElectrolux washer codes

Reed switch fault – dispenser drawer reed switch circuit interrupted.

First step from the service manual

Check if dispenser drawer is closed and inspect magnet and reed switch (Test 3).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E14.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E14 means on a Electrolux washer

The E14 error code on an Electrolux washer indicates a fault in the reed switch circuit associated with the dispenser drawer. A reed switch is a small magnetically-actuated electrical switch that opens or closes depending on the proximity of a magnet. In this application, a magnet is mounted on the dispenser drawer, and a corresponding reed switch is mounted on the washer body. When the drawer is properly closed, the magnet aligns with the reed switch, completing the circuit and signaling the control board that the drawer is in the correct position. If that circuit is interrupted for any reason, the control board registers the E14 fault.

The most common triggers for this code include a drawer that is not fully closed, a misaligned or dislodged magnet on the drawer assembly, a damaged or failed reed switch, or a wiring issue in the circuit connecting the reed switch to the control board. Physical damage to the reed switch from vibration or impact is also possible, as these components are fragile glass-enclosed devices. Corrosion or moisture intrusion at the switch or connector terminals can also break the circuit intermittently.

Diagnosis should begin by confirming the dispenser drawer is fully seated and closed, then visually inspecting the magnet on the drawer for displacement or loss. If both appear intact, the next step is to perform Test 3 as referenced in the diagnostic procedure, which evaluates the reed switch circuit directly. This test typically involves checking continuity through the switch when the magnet is in position and verifying that the circuit opens when the magnet is removed.

Source: manufacturer service documentation.

Common causes of E14

  1. 01

    Dispenser drawer not fully closed

    Wiring / connection

    If the drawer is slightly ajar or has not clicked into its fully seated position, the magnet will not align with the reed switch and the circuit will remain open. Push the drawer firmly until it seats completely and restart the cycle.

  2. 02

    Dislodged or missing drawer magnet

    Part replacement

    The magnet mounted on the dispenser drawer can shift out of position or detach over time due to repeated use or impact. Inspect the drawer for the presence and secure positioning of the magnet, which is typically found on the rear or side of the drawer assembly.

  3. 03

    Failed or damaged reed switch

    Part replacement

    Reed switches contain a fragile sealed glass envelope and can fail due to physical shock, vibration, or age. A failed switch will show no continuity even when the magnet is correctly positioned directly adjacent to it.

  4. 04

    Wiring or connector fault in the reed switch circuit

    Wiring / connection

    A broken wire, loose connector, or corroded terminal between the reed switch and the control board can interrupt the circuit and trigger E14. Inspect the wiring harness and connector at the reed switch for damage, corrosion, or loose pins.

  5. 05

    Control board unable to read the reed switch signal

    Part replacement

    If the reed switch and wiring check out correctly but the error persists, the control board input receiving the switch signal may be at fault. This is the least common cause and should only be considered after all other components have been tested and confirmed good.

See the test procedure for each cause

Frequently asked questions about E14

What does E14 mean on a Electrolux washer?
E14 indicates a fault in the dispenser drawer reed switch circuit, meaning the washer cannot confirm the drawer is properly closed. The machine uses a magnet on the drawer and a reed switch on the body to detect drawer position. When that circuit is interrupted, the control board logs E14 and may halt the cycle. The fault can stem from an open drawer, a missing magnet, a failed switch, or a wiring problem.
How do I fix the E14 error on my Electrolux washer?
Start by firmly closing the dispenser drawer and checking that it is fully seated. Then visually inspect the drawer for a small magnet on its body, confirming it is present and secure. If both check out, the reed switch itself should be tested for continuity using a multimeter with the magnet held close to it, following the Test 3 diagnostic procedure. Depending on findings, the magnet, reed switch, or associated wiring may need to be repaired or replaced.
Is it safe to use my Electrolux washer while the E14 error is showing?
Running the washer while E14 is active is generally not recommended. The error indicates the machine cannot confirm the dispenser drawer is properly closed, and operating with a partially open drawer could allow water or detergent to escape from the dispenser area. It is best to resolve the fault before continuing to use the appliance.
Will resetting my Electrolux washer clear the E14 code?
A reset may temporarily clear the error code, but if the underlying fault in the reed switch circuit has not been corrected, the code will return once the machine attempts to read the drawer position again. Address the root cause, such as closing the drawer, securing the magnet, or replacing the reed switch, before attempting a reset to avoid repeated faults.
How much does it cost to repair an E14 error on an Electrolux washer?
If the issue is simply a drawer that was not fully closed, there is no cost involved. Replacing a dislodged or missing drawer magnet is typically a low-cost fix, generally in the range of a few dollars to around twenty dollars for the part. A reed switch replacement may cost between fifteen and fifty dollars for the part, with additional labor costs if a technician is required. If the control board is at fault, repair costs will be considerably higher, often ranging from one hundred fifty to three hundred fifty dollars or more depending on parts and labor.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass