mypros+
Error code reference

Electrolux Washer Error Code ED6

No communication between PCB and display board (INPUT)

Electrolux codesElectrolux washer codes

No communication between PCB and display board (INPUT) - wiring faulty between PCB and programme display board, or PCB faulty.

First step from the service manual

Check wiring between PCB and programme display board; check PCB.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for ED6.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What ED6 means on a Electrolux washer

The ED6 error code on an Electrolux washer indicates a failure in communication between the main PCB (printed circuit board) and the programme display board. These two boards exchange data continuously during operation, and when that communication link breaks down, the machine cannot coordinate user inputs with its control logic. The washer will typically halt operation and display ED6 to alert the user that this internal link has failed.

The most common root cause is a wiring fault between the two boards. This can include loose or unseated connectors, broken wire harness pins, chafed or shorted wiring, or corrosion on the connector terminals. Because the wiring harness runs through areas that can experience vibration and moisture, physical damage to the loom is a realistic possibility, especially on older machines or those that have experienced rough handling.

If the wiring harness and connectors are found to be intact and in good condition, the fault likely points to the PCB itself. A failed main control board will be unable to send or receive the signals required to communicate with the display board. In some cases the display board may be the failed component, though the error description specifically highlights the PCB as the primary suspect after wiring has been ruled out. Proper diagnosis requires a visual inspection of the harness, connector integrity checks, and potentially testing board voltages.

Source: manufacturer service documentation.

Common causes of ED6

  1. 01

    Loose or disconnected wiring connector

    Wiring / connection

    The connector linking the PCB to the programme display board may have worked loose due to vibration over time. Inspect both ends of the harness for connectors that are not fully seated and press them firmly back into place.

  2. 02

    Damaged or chafed wire harness

    Part replacement

    The wire loom between the two boards can suffer abrasion, pinching, or breaks, especially where it passes through the cabinet frame. Look for visible damage to insulation, broken wires, or burnt spots along the full length of the harness.

  3. 03

    Corroded or dirty connector terminals

    Wiring / connection

    Moisture inside the cabinet can cause oxidation on the connector pins, increasing resistance and disrupting the communication signal. Inspect terminals for green or white corrosion and clean with electrical contact cleaner if found.

  4. 04

    Faulty main PCB

    Part replacement

    If the wiring and connectors are confirmed to be in good condition, the main control board may have failed internally. A failed PCB will need to be replaced, as internal board faults are not field-repairable.

  5. 05

    Faulty programme display board

    Part replacement

    Although the error points primarily to the PCB, the display board itself can fail and break the communication link. If the PCB has been ruled out, the display board should be tested or replaced.

See the test procedure for each cause

Frequently asked questions about ED6

What does ED6 mean on a Electrolux washer?
ED6 means the main PCB and the programme display board have lost communication with each other. This can be caused by a faulty wiring harness, loose connectors between the two boards, or a failed PCB. The washer will not operate normally until the fault is identified and corrected.
Can I fix an ED6 error myself on my Electrolux washer?
In some cases, yes. Start by unplugging the washer and inspecting the wiring harness and connectors that run between the main PCB and the display board. If a connector is loose or a wire is visibly damaged, this is something a confident DIYer can address. If the boards themselves need replacement, that repair requires more technical skill and comfort working with control electronics.
Will resetting my Electrolux washer clear the ED6 error code?
A reset may temporarily clear the code, but if the underlying wiring fault or board failure is still present, the error will return once the machine attempts to resume communication between the PCB and display board. A reset is worth trying first, but it is not a fix for the actual fault.
Is it safe to use my Electrolux washer when it shows ED6?
You should not continue to operate the washer while ED6 is active. The loss of communication between the control board and display board means the machine cannot reliably process user commands or monitor its own operation, which could lead to unpredictable behavior during a cycle.
How much does it cost to repair an ED6 error on an Electrolux washer?
If the fix is simply reseating a connector or repairing a damaged wire, costs can be minimal, typically covering only service call fees in the range of $75 to $150. If the main PCB needs replacement, parts and labor combined can range from $200 to $400 or more depending on the specific model and the cost of the replacement board.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass