Model reference
Electrolux EWM2100
Washer
4 documents84 error codes19 service modes
Available documentation
Service Manual
- SERVICE MANUAL LAVAGE - Guide pour le diagnostic des contrôles électroniques ENV0695 pg
- Service Manual СТИРКА Wm-wd185 pg
Other
- 670HU95 pg
- Electrolux EWM2100 ZKG2125 zanussi washing machine guide176 pg
MyPros+ Max
Diagnose your Electrolux EWM2100.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (84)
CodeMeaning
E00No fault present.E11Water fill difficulty during wash cycleE12Water fill difficulty during drying cycleE13Water leak detectedE21Drain difficulty during washE22Drain difficulty during drying cycle.E23Drain pump triac defective.E24Drain pump triac detection circuit faultE31Analog pressure switch signal out of limits sent to main board.E32Analog pressure switch calibration errorE33Mismatch between anti-boiling contact closure and first level pressure switch…E34Mismatch between electronic pressure switch level and anti-boiling pressure…E35Water level too highE36Anti-boiling pressure switch sensing circuit fault.E37First level pressure switch sensing circuit fault.E38Pressure switch air trap cloggedE39Overflow protection high-voltage sensing circuit fault.E3AHeater relay detection circuit faultE41Door open detectedE42Door opening problemsE43Door lock delay triac defective.E44Closed door detection circuit defective.E45Door lock delay triac detection circuit defectiveE51Motor supply triac short-circuitE52No signal from motor tachometer generatorE53Motor triac detection circuit defectiveE54Motor relay contacts stuckE57Inverter drawing too much current (>15A).E58Motor drawing too much current (>4.5A).E59No tachogenerator signal for more than 3 seconds.View all 84 error codes
E5AInverter heatsink overheating.E5BInput voltage below 175V (ENV06 shown as E5H).E5CInput voltage too high.E5DData transmission error between inverter and main board.E5ECommunication error between main board and inverter.E5FMotor start failure from inverter board.E61Insufficient heating during washE62Overheating during wash cycleE66Heater relay contacts permanently closedE68Current leakage at wash heaterE69Wash heater element open circuit / interrupted.E71Wash NTC temperature sensor faultE72Dryer condenser NTC temperature sensor faultE73Dryer duct NTC temperature sensor faultE74Wash NTC temperature sensor incorrectly positioned.E82Program selector cancel/stop position read errorE83Program selector code read errorE84Recirculation pump faultE85Recirculation pump triac sensing circuit faultE91Communication error between display board and main boardE92Configuration data mismatch protocol errorE93Appliance configuration errorE94Wash cycle configuration errorE95No communication between EEPROM and microprocessor.E96Mismatch between hardware version and configuration setting.E97Mismatch between selector version and configuration data.E98Communication error between main board and inverter (or microprocessor and…E9FCommunication error between main board and external devices.EA1Drum positioning system (DSP) defective (top-loading machines)EA6Drum door defective (top-loading machines)EB1Mains power supply frequency out of acceptable range.EB2Mains supply voltage too high.EB3Mains supply voltage too low.EBEMismatch between safety relay and sensing circuit on main board.EBFSafety system sensing circuit faultEC1Fill valves stuck/blocked with flow meter operating.EC2Water turbidity sensor signal out of range.EC3Weight sensor signal out of range or no signal.Ed1Data communication error between main board and WD (dryer) board.Ed2Dryer heater element 1 defective.Ed3Dryer heater element 2 defective.Ed4Dryer relay defectiveEd6No communication between main board and satellite display board (INPUT…EF1Drain hose blocked/kinked/too high or drain filter dirtyEF2Excessive detergent dosage (too much foam during draining) or drain hose/filter…EF3Aqua Control system activatedEF4Low water fill pressure with no flow meter signal and fill valve open.EF5Unbalanced loadEF6Appliance reset.EH1Mains frequency out of configured limits.EH2Supply voltage too highEH3Supply voltage too lowEHEMismatch between safety relay and sensing circuit (ENV06 variant of EBE).EHFSafety system sensing circuit fault
Service modes (19)
- alarm_clear1
- diagnostic1
- diagnostic_AEG_New_right_selector["1
- diagnostic_AEG_NexXxt["1
- diagnostic_CLUB_DISPLAY["1
- diagnostic_DELTA_no_selector["1
- diagnostic_ENV06_all_models["1
- diagnostic_ENV06_INPUT_model["1
- diagnostic_EWM1000_horizontal_buttons["1
- diagnostic_EWM1000_vertical_buttons["1
- diagnostic_EWM1000plus_selector_combined_with_ON_OFF["1
- diagnostic_EWM1000plus_selector_with_separate_ON_OFF["1
- diagnostic_LCD_no_selector_separate_ON_OFF["1
- diagnostic_LCD_with_selector_separate_ON_OFF["1
- fault_code_deletion_ENV06["1
- fault_code_deletion_EWM1000["1
- quick_alarm_readDuring normal operation or program execution, simultaneously press the START/PAUSE button and the…
- quick_fault_code_view_ENV06["Hold START/PAUSE and nearest OPTION button for 2 seconds
- quick_fault_code_view_EWM1000["Hold START/PAUSE and an OPTION button (horizontal layout) or buttons 2 and 3 (vertical layout)…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax