mypros+
Error code reference

Electrolux Washer Error Code E92

Inconsistency in communication between main board and display board (versions not compatible)

Electrolux codesElectrolux washer codes

Inconsistency in communication between main board and display board (versions not compatible) - wrong control/display board or wrong main board (not right for model).

First step from the service manual

Verify correct control/display board and main board are installed for the model.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E92.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E92 means on a Electrolux washer

The E92 error code on an Electrolux washer indicates a communication incompatibility between the main control board and the display board. Specifically, the firmware versions or hardware configurations of these two boards do not match, causing the control system to flag an inconsistency. This is not a typical communication failure caused by a loose wire or signal noise. Instead, it points directly to a version mismatch where one or both boards are not the correct part for the specific model installed.

This situation most commonly arises after a board replacement where an incorrect replacement part was sourced. If a technician or owner installs a main board or display board that was designed for a different model or a different production run, the two boards may fail to establish valid communication because their internal protocols or firmware versions do not align. The washer cannot operate safely or correctly when this condition exists, so it halts and displays E92.

Diagnosing this code requires confirming that both the main board and the display board are the exact correct parts for the specific model number of the washer. Cross-referencing each installed board against the model's parts list is the essential first step. If either board was recently replaced, that replacement part is the most likely source of the incompatibility and should be verified and potentially exchanged for the correct version.

Source: manufacturer service documentation.

Common causes of E92

  1. 01

    Incorrect replacement main board installed

    Part replacement

    A main control board sourced for a different model or production run was installed during a prior repair. Even boards that appear physically identical can carry incompatible firmware versions.

  2. 02

    Incorrect replacement display board installed

    Part replacement

    The display or control panel board installed does not match the version required by the main board in this specific model. Verify the display board part number against the model's parts list.

  3. 03

    Mixed board set from different model variants

    Part replacement

    Both boards may have been swapped at separate times, resulting in a combination of parts that were never designed to work together. Each board must be matched not just to the model, but to the same compatible revision.

  4. 04

    Board installed from a non-matching regional or production variant

    Part replacement

    Some Electrolux models share similar chassis but have region-specific or production-run-specific boards. A board sourced from a different variant may trigger E92 even if the model name appears identical.

See the test procedure for each cause

Frequently asked questions about E92

What does E92 mean on a Electrolux washer?
E92 means the main control board and the display board installed in your washer are not compatible with each other. The error indicates a version or configuration mismatch between these two components rather than a wiring fault or sensor failure. The washer detects that the two boards cannot communicate correctly and shuts down to prevent improper operation. Resolving it requires confirming that both boards are the exact correct parts for your specific model.
Can I fix the E92 error myself on my Electrolux washer?
You can start by checking whether any boards were recently replaced in the machine and verifying that the installed parts are correct for your model number. If you have access to the parts list for your specific model, compare the part numbers on the installed main board and display board. If an incorrect part is identified, replacing it with the correct version is the fix. This type of repair involves working with control electronics, so comfort with appliance repair is recommended.
Will resetting my Electrolux washer clear the E92 error?
A reset will not clear the E92 error because the problem is a hardware and firmware incompatibility, not a temporary glitch. Each time the washer powers on and the two boards attempt to communicate, the mismatch will be detected again and the code will return. The error will only be resolved by installing the correct, compatible board or boards for your model.
Is it safe to use my Electrolux washer when it shows E92?
The washer will typically not operate normally when E92 is active, as the control system flags the incompatibility and prevents standard function. Attempting to force operation with mismatched control boards is not advisable, since the machine may not respond to commands correctly or safely. It is best to address the board compatibility issue before running the appliance.
How much does it cost to fix the E92 error on an Electrolux washer?
Cost depends on which board or boards need to be replaced. A main control board for an Electrolux washer typically costs in the range of $100 to $300 for the part alone, while a display board can range from $50 to $200. If professional labor is involved, expect additional costs depending on local rates. If only one board needs to be swapped out for the correct version, the total expense is generally on the lower end of that range.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass