mypros+
Model reference

Electrolux EWFLS65IMB0

Washer

8 documents47 error codes13 service modes

Available documentation

Service Manual

  • FRONT-LOAD WASHING MACHINE Model No. EWFLS65I10 pg
    Covers this model
  • Use & Care Guide - Wave-Touch™ Front-Load Washer46 pg
    Covers this model
  • Wave-Touch™ and IQ-Touch™ Front-Load Washer Models EIFLW55H & EWFLW65H Technical Service Manual92 pg
    Covers this model

Tech Sheet

  • Washer Tech Data Sheet16 pg
    Covers this model

Service Flash

  • Service Flash LN0903 Dispenser Drawer Will Not Remain In The Closed Position4 pg
    Covers this model
  • SERVICE FLASH LN0902 Check Hoses Error1 pg
    Covers this model
  • Service Flash LN0907 Water Found on Door Ring1 pg
    Covers this model

Installation Guide

  • Use & Care Guide - Wave-Touch™ Front-Load Washer44 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EWFLS65IMB0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (47)

CodeMeaning
E11Fill time too long.E13Water leak in tub or air leak in air bell.E21Water not pumping out fast enough.E31Electronic pressure switch failure.E32Pressure sensor calibration problem.E35Pressure sensor indicates water overfill.E38Air trap clogged.E41Control board thinks the door switch is open.E42Door lock device failure.E44Door closed sensing failure.E45Line door sensing failure.E46Door command sense failure.E49Door incongruence between door line and door sense.E52Bad signal from tachogenerator.E53Low voltage to Motor Control Board.E54Over speed condition.E55Under speed condition.E57High current on inverter.E58High current on motor phase.E59No tachogenerator signal for 3 seconds.E5AHigh temperature on heat sink caused by overloading.E5CHigh voltage experienced by motor control board.E5DCommunication problem between main control board and motor control board.E5ECommunication problem between main control board and motor control board.E5FMotor control board is continuously resetting.E67Heater sensing relay failure.E68Current leakage to ground on heater or fuse opened.E69Heating element relay failure.E71Drum water NTC (tub heater thermistor) failure.E74Wash temperature does not increase.
View all 47 error codes
E91Communication error between UI board and main control board.E92User Interface to Main Board communications error.E93Console or Main Board control problem.E94Main Board control problem.E95Communication problem between microprocessor and external EEPROM.E97Console or Main Board control problem.E98Console control problem.E9FCommunication protocol error.EA1Power supply frequency out of limits.EA2Power supply voltage too high.EA3Power supply voltage too low.EA5Main voltage sensing failure.EAELine safe relay sensing failure.EF1Clogged drain pump.EF2Too much soap detected.EF5Incorrect water temperature.EF8Key stuck on control panel.

Service modes (13)

  • Clear Stored Error Codes["Press CANCEL to enter standby mode.","Within 10 seconds, press any button to wake up the…
  • control_lock["Navigate to CONTROL LOCK (VERR COMM) option using scroll buttons","Press SELECT","Message…
  • Demo Mode (IQ Touch)["Turn the cycle selector knob to SPIN ONLY cycle, press the START button then the CANCEL…
  • Demo Mode (Wave Touch)["Turn the cycle selector knob to SPIN ONLY cycle, press the START button then the CANCEL…
  • demo_mode_exit["Press and hold SPIN SPEED and SOIL LEVEL buttons simultaneously for 5 seconds to exit demo mode…
  • Diagnostic Test Mode["Press the CANCEL button to enter standby mode.","Within 10 seconds after pressing CANCEL, press…
  • Installation Cycle (IQ Touch)["Wake the washer up by pressing any button (except the cancel button).","Rotate the cycle knob to…
  • Installation Cycle (IQ-Touch)["Empty washer drum and close door.","Wake washer by pressing any button.","Rotate cycle knob to…
  • Installation Cycle (Wave Touch)["After plugging in the washer the first time, wake up the washer by pressing any button and follow…
  • Installation Cycle (Wave-Touch)["After plugging in washer the first time, wake up by pressing any button.","Follow prompts on LCD…
  • installation_program["Navigate to 'Set Preferences' (rég préf) option using scroll buttons","Press SELECT to access…
  • Read Error Codes["Wake the washer by pressing any button (except CANCEL).","Press and hold the CANCEL and START…
  • Reset Factory Defaults (IQ-Touch)["Wake machine.","Press and hold the spin speed and soil selection keys simultaneously until you…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax