mypros+
Model reference

Electrolux EWM21XX

Washer

1 document77 error codes5 service modes

Available documentation

Service Manual

  • Service Manual Washing TC2 TC3 TC478 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EWM21XX.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (77)

CodeMeaning
E10Water fill difficulty (tap closed)E11Water fill difficulty during washing cycle.E12Water fill difficulty during drying cycle.E13Water leaks detected (drain tube improperly positioned, water pressure too low…E20Drain difficulty (filter dirty)E21Drain difficulty during washing cycle.E22Drain difficulty during drying cycle.E23Faulty triac for drain pump.E24Malfunction in sensing circuit on triac for drain pump (wrong input voltage to…E31Malfunction in electronic pressure switch circuit (frequency of signal from…E32Calibration error of the electronic pressure switch (signal with unstable…E35Overflow condition detected (water fill solenoid valve faulty, pressure switch…E38Internal pressure chamber is clogged (water level does not change for at least…E3AFaulty sensing by heating element relay (input voltage to microprocessor always…E40Door openE41Door open (detected after 15 seconds).E42Problems with door lock (electrical current leak between heating element and…E43Faulty triac supplying power to door delay system.E44Faulty sensing by door delay system.E45Faulty sensing by triac on door delay system (wrong input voltage to…E51Motor power triac short-circuited.E52No signal from motor tachometric generator.E53Motor triac sensing circuit faulty (wrong input voltage to micro-processor).E54Motor relay contacts sticking (high voltage level when the relay switches to…E57Inverter is drawing too much current (>15A).E58Inverter is drawing too much current (>4.5A), motor malfunction or overload.E59No signal from tachometric generator for 3 seconds.E5AOverheating on heat dissipator for inverter.E5CInput voltage is too high.E5dData transfer error between inverter and main PCB.
View all 77 error codes
E5ECommunication error between inverter and main PCB.E5FInverter PCB fails to start the motor.E5HInput voltage is lower than 175V.E61Insufficient heating during washing cycle.E62Overheating during washing (temperature higher than 88°C for more than 5…E66Heating element power relay faulty (incongruence between sensing and relay…E68Earth-leakage detected (value of grid voltage different from main value).E69Heating element interrupted (thermal fuse open).E71NTC sensor for wash cycle faulty (short-circuited or open).E72Fault in NTC sensor on drying condenser (voltage out of range, short-circuit or…E73Fault in NTC sensor on drying duct (voltage out of range, short-circuit or open…E74NTC sensor for wash cycle improperly positioned.E82Error in selector reset position.E83Error in reading selector.E91Communication error between main PCB and display.E92Communication incongruence between main PCB and display (incompatible versions).E93Appliance configuration error.E94Incorrect configuration of washing cycle.E95Communication error between micro-processor and EEPROM.E97Incongruence between programme selector and cycle configuration.E98Communication error between main PCB and inverter (incompatibility between main…E9bCommunication error between micro-processor and FLASH memory.E9CAppliance configuration error.E9dClock faulty.E9FCommunication error between main PCB and inverter board.E9HCommunication error between micro-processor and FLASH memory.EC1Solenoid valve blocked with operating flowmeter.EC3Problems with weight sensor (no signal or outside the limits).Ed1Data transfer error between WD PCB and main PCB.Ed2Drying heating element relay 1 faulty.Ed3Drying heating element relay 2 faulty.Ed4Relay which switches the power between the washing and drying heating element…Ed6No communication between main PCB and display board (INPUT).Ed7No communication between main PCB and remote display board.EF0Water leakage detected by Aqua Control System.EF1Drain filter clogged or drain phase too long.EF2Overdosing of detergent (too much foam during drain phases).EF3Aqua control system intervention due to water leaks.EF4Water fill pressure too low, no signal from flowmeter and solenoid valve is…EF5Unbalanced load detected, final spin phases skipped.EF6Reset alarm.EH0Voltage or frequency outside the normal values.EH1Supply frequency of appliance outside the limits.EH2Supply voltage too high.EH3Supply voltage too low.EHEIncongruence between safety relay (in the main PCB) and safety sensing circuit.EHFSafety sensing circuit faulty (wrong input voltage to micro-processor).

Service modes (5)

  • alarm_deletion1
  • demo1
  • diagnostic1
  • operating_time_counter1
  • rapid_alarm_readingPress the START/PAUSE button and the nearest option button simultaneously (as if entering…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax