mypros+
Error code reference

Electrolux Washer Error Code E82

Error in reset position of selector

Electrolux codesElectrolux washer codes

Error in reset position of selector - circuit board faulty or wrong configuration data; selector or wiring issue.

First step from the service manual

Check circuit board; check selector; check wiring.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E82.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E82 means on a Electrolux washer

The E82 error code on an Electrolux washer indicates a fault in the reset position of the cycle selector. Specifically, the machine's control system cannot correctly read or establish the selector's home or reference position. This involves communication between the selector switch assembly and the main circuit board, where configuration data is used to identify the selector's starting point during initialization. When this reference position cannot be confirmed, the washer flags the error and halts normal operation.

There are two primary failure pathways for E82. The first involves the main circuit board itself, either a hardware fault on the board or incorrect configuration data stored within it. The second involves the selector switch or the wiring connecting it to the board. Damaged wiring, loose connectors, or a worn and failing selector switch can all disrupt the signal needed to confirm the reset position. Because both the board and the selector are implicated, systematic diagnosis is required to isolate the actual source.

Diagnostic procedure should begin with a visual and physical inspection of the wiring harness between the selector and the control board, checking for damaged insulation, corroded terminals, or loose connectors. The selector switch itself should then be tested for proper function and continuity. If wiring and the selector check out as serviceable, attention turns to the main circuit board, which may require reprogramming or replacement if configuration data is corrupt or the board has failed internally.

Source: manufacturer service documentation.

Common causes of E82

  1. 01

    Faulty selector switch

    Part replacement

    The selector switch can wear out over time, losing the ability to send a reliable signal for its reset position. Testing continuity through the switch positions will reveal whether it is functioning correctly.

  2. 02

    Damaged or loose wiring harness

    Wiring / connection

    Wiring between the selector and the control board can develop loose connections, corrosion, or physical damage. Inspect the full harness and connector terminals for any visible problems or intermittent contact.

  3. 03

    Incorrect or corrupt configuration data on the circuit board

    Wiring / connection

    The main control board stores configuration data used to recognize the selector's reset position. If this data is corrupt or mismatched for the machine's configuration, the error will trigger even when hardware components are intact.

  4. 04

    Faulty main circuit board

    Part replacement

    If the board has an internal hardware failure, it may be unable to process the selector's position signal correctly. This is typically confirmed only after the selector and wiring have been ruled out as causes.

See the test procedure for each cause

Frequently asked questions about E82

What does E82 mean on a Electrolux washer?
E82 indicates an error in the reset position detection of the cycle selector. The washer cannot confirm the selector's home position during initialization, which prevents normal operation. The fault can originate from the selector switch, the wiring connecting it to the control board, or the control board itself including its stored configuration data.
Can I fix the E82 error myself?
Some steps are accessible to a knowledgeable DIYer, such as inspecting the wiring harness for loose connectors or visible damage and checking the selector switch for obvious wear. However, diagnosing a faulty circuit board or correcting configuration data typically requires technical experience and proper tools. If basic wiring and selector checks do not resolve the error, professional service is recommended.
Is it safe to keep using my Electrolux washer with an E82 error?
The washer will generally stop operating when E82 is active, which limits the risk of further damage during a cycle. It is not advisable to attempt to force the machine to run while the error is present, as the underlying selector or board fault could cause unpredictable behavior. Address the error before resuming regular use.
Will resetting the washer clear the E82 error?
A reset may temporarily clear the error code, but it will return if the underlying hardware fault is not corrected. If the selector switch, wiring, or control board has a genuine defect, the reset position error will reappear as soon as the machine attempts to initialize again. A reset is useful for ruling out a transient glitch but is not a reliable fix.
How much does it cost to repair an E82 error on an Electrolux washer?
Repair costs depend on which component has failed. Replacing a selector switch is typically the least expensive repair, with parts and labor generally ranging from around $75 to $200. A main control board replacement is more costly, often ranging from $200 to $400 or more depending on the specific model and labor rates in your area. Getting a diagnostic from a qualified technician first can help avoid replacing parts unnecessarily.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass