Model reference
Electrolux 7000
Washer
3 documents55 error codes13 service modes
Available documentation
Service Manual
- Service Manual Affinity Washer 6000 & 7000 Series100 pg
- Service Manual Affinity Horizontal Axis Washer 6000 & 7000 Series100 pg
- All About Servicing Affinity Front Load 6000 & 7000 Series 3.5 Cu. Ft. Washers74 pg
MyPros+ Max
Diagnose your Electrolux 7000.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (55)
CodeMeaning
E10Communication failure between control board components.E11Fill time too longE12Communication failure between control board components.E13Water leak in tub or air leak in air bell system.E21Water not pumping out fast enough.E23Drain pump relay on control board failed.E24Drain pump relay on control board failed.E25Open control thermistor.E31Pressure sensor not communicating with control board.E35Pressure sensor indicates water overfill.E36Control board problem.E41Control board thinks the door switch is open.E43Board communications problem.E44Board communications problem.E45Board communications problem.E46Board communications problem.E47Board thinks the door PTC circuit is open in spin.E48Board thinks the door PTC circuit is closed.E4AThe drying time has exceeded the program time for the cycle.E52Bad signal from tachogenerator.E56High motor current.E57High current on inverter.E58High current on motor phase.E59No tachogenerator signal for 3 seconds.E5AHigh temperature on heat sink of speed control board.E5BHigh temperature on heat sink.E5CHigh temperature on heat sink.E5DCommunication problem between control board and speed control board.E5ECommunication problem between control board and speed control board.E5FCommunication problem between control board and speed control board.View all 55 error codes
E66Heating element relay failure.E67Input voltage on microprocessor incorrect.E68Current leakage to ground on heater or fuse opened.E74Wash temperature does not increase.E75Water temperature sensor circuit problem.E76NTC temperature for the cold water valve over the limits.E82Console control problem.E83Console control problem.E8CHigh limit thermostat has tripped too many times in a certain amount of time.E91Selector LEDs do not light up.E93Console control problem.E94Console control problem.E95Communication error.E97Console control problem.E98Console control problem.E9ELine voltage problem (low voltage or intermittent voltage).EAFMicrocontroller has been reset by Watchdog timer.EB1Incoming power frequency out of limits.EB2Incoming line voltage above 130 VAC.EB3Incoming line voltage below 90 VAC.EBEConsole control problem.EBFConsole control problem.EF1Clogged drain pump.EF2Too much soap/oversudsing.EF5NTC temperature for the hot water valve over the limits.
Service modes (13)
- Clear Latest Stored Error Code1
- clear_error_code1
- Control LockPress Options and Select at the same time and hold for 10 seconds
- control_lockPress Options and Select at the same time and hold for 10 seconds until 'LOC' is displayed.
- diagnostic1
- Diagnostic Test1
- Factory Settings ResetPress Start/Pause and Select at the same time and hold until the signal sounds.
- Field Test Mode (Error Code Reading)1
- Function Test Mode1
- Read Error Codes["Wake the washer by pressing any button.","Wait 5 seconds.","Press and hold the START/PAUSE and…
- read_error_codes1
- Reading Error Codes1
- reset_factory_settingsPress Start/Pause and Select at the same time and hold until a signal sounds.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax