Model reference
Electrolux EWT1066TDW
Washer
1 document61 error codes5 service modes
Available documentation
Service Manual
- Service Manual Washing99 pg
MyPros+ Max
Diagnose your Electrolux EWT1066TDW.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (61)
CodeMeaning
E10Water fill difficulty (tap closed).E11Water fill difficulty during washing.E13Water leaks.E20Drain difficulty (filter dirty).E21Drain difficulty during washing.E23Faulty TRIAC for drain pump.E24Drain pump TRIAC sensing circuit faulty.E31Malfunction in electronic pressure switch circuit.E32Calibration error of the electronic pressure switch.E35Overflow.E38Internal pressure chamber is clogged (water level does not change for at least…E40Door open.E41Door openE42Door openE43Faulty triac supplying power to door delay system.E44Faulty sensing of door delay system.E45Faulty sensing by door delay system TRIAC.E52No signal from motor tachometric generator.E57Inverter is drawing too much current (>15 A).E58No signal from tachometric generator for 3 seconds.E59Input voltage is lower than 175 V.E5AOverheating on heat dissipater for inverter.E5CInput voltage is too high.E5DData transfer error between inverter and main PCB.E5ECommunication error between inverter and main PCB.E5FInverter is drawing too much current (>4.5 A).E5HInverter PCB fails to start the motor.E61Heating element interrupted.E62Overheating during washing phase (temperature higher than 88°C for more than 5…E66Heating element power relay faulty (inconsistency between sensing and relay…View all 61 error codes
E68Current leak to the ground.E69Insufficient heating during the washing phase.E6AHeating relay sensing faulty.E6HHeating element power relay faulty (inconsistency between sensing and relay…E71NTC probe for wash cycle faulty (short-circuited or open).E74NTC probe for wash cycle improperly positioned.E83Error in reading selector.E86Selector configuration error.E87Display board microprocessor faulty.E91Communication error between main PCB and display board.E92Communication inconsistency between main PCB and display board (incompatible…E93Appliance configuration errorE94Appliance configuration errorE97Appliance configuration errorE98Display board configuration error.E9CDisplay board touch sensor faulty.E9EAppliance configuration error.EA1No drum position signal made (no signal from the DSP during motor activation).EA6No signal from the DSP during motor activation.EC1Electronically controlled valve blocked with operating flowmeter.EF0Excessive detergent / Water leakage (Aqua Control System).EF1Drain filter clogged (drain phase too long).EF2Overdosing of detergent (too much foam during drain phases).EF3Aqua control system intervention.EF4Water fill pressure too low, no signal from flowmeter and electronically…EF5Unbalanced loadEF6Electronically controlled valve blocked with operating flowmeter.EH0Voltage or frequency outside normal values.EH1Appliance power supply frequency out of limits.EH2Supply voltage too high.EH3Supply voltage too low.
Service modes (5)
- alarm_deletion1
- demo1
- diagnostic1
- operating_time_counter1
- rapid_alarm_readingTouch the START/PAUSE sensor and the nearest option sensor simultaneously and hold for at least 2…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax