Model reference

Electrolux FFLE40C3QW0

Washer

3 documents44 error codes2 service modes

Available documentation

Service Manual

Use & Care of your Laundry Center22 pg
Covers this model

Other

599566344912 pg
Covers this model

Installation Guide

Installation of your Laundry Center64 pg
Covers this model

MyPros+ Max

Diagnose your Electrolux FFLE40C3QW0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Electrolux Washer

E11 on my Electrolux FFLE40C3QW0

M+

Fill time too long (washer).

From Service Manual 683886, p.18:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part 5304504863

Electronic control board

Error codes (44)

CodeMeaning

E11Fill time too long (washer).E21Water not pumping out fast enough (washer).E31Electronic pressure switch failure (washer).E32Pressure sensor calibration problems (washer).E35Pressure sensor indicates water overfill (washer).E41Control board thinks lid switch is open (washer).E42Lid lock device failure (washer).E43Control board fails to lock lid (washer).E44Lid closed sensing failure (washer).E45Lid locked sensing failure (washer).E46Lid lock command sensing failure (washer).E49Lid incongruence between lid closed sensing and lid locked sensing (washer).E4ALid locked triac sensing failure on control board (washer).E51Motor relay stuck open, locked rotor, harness fault, low power supply, thermal…E52Tachometer signal missing (washer).E53Low voltage to control board (washer).E54Centrifugal switch 2, heater, or thermal limiter-2 fault; centrifugal switch 2…E55Motor sensing failure on main board E56Belt broken or loose (dryer).E57High current on inverter (washer).E58High current on motor phase (washer).E59Incongruence between real motor speed and expected motor speed (washer).E5AHigh temperature on heat sink on control board (washer).E5CVoltage too high on control board (washer).E61Heater relay failure E62Heating timeout E65High limit thermostat trip count too high E67Heater sensing failure on main board E71NTC failure E72NTC failure

View all 44 error codes

E75Valve NTC failure (washer).E81Program selector/encoder fault E82Key-stuck error E91Communication error between UI board and control board (washer).E92Communication error between UI board and control board (washer).E93Software configuration error E94Software configuration error E97Software configuration error EA1Line frequency out of limits (54Hz<Lf<46Hz for 50Hz system, 64Hz<Lf<56Hz for…EA2High line voltage EA3Low line voltage EA5Line amplitude sensing failure on main board EAELine safe relay sensing failure (washer).EF1Clogged drain pump (washer).

Service modes (2)

Dryer Diagnostic Mode (Factory Line-Test Mode)["1. Place the Cycle Selector knob at Position 0 (12 o'clock).","2. Set the Temperature Selector to…
Washer Diagnostic Mode["1. Knobs can be in any position.","2. If unit is unplugged, perform Cold Power On and go to step…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass