mypros+
Error code reference

Electrolux Washer Error Code dr

Door switch is not closed.

Electrolux codesElectrolux washer codes

Door switch is not closed.

First step from the service manual

Check that the door is closed and the door catch is not broken. If so, replace the door lock assembly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for dr.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What dr means on a Electrolux washer

The dr error code on an Electrolux washer indicates that the door switch circuit is not registering a closed-door signal. The washer's control board continuously monitors the door lock assembly to confirm the door is physically closed and latched before allowing a wash cycle to begin or continue. When the control board does not receive the expected closed-circuit signal from the door switch, it halts operation and displays the dr code to prevent the machine from running with an open or unlatched door.

The door lock assembly contains both a mechanical latch mechanism and an electrical switch. The mechanical side engages the door catch to hold the door shut, while the electrical switch sends a signal to the control board confirming closure. If either the physical door catch is broken or misaligned, or if the switch inside the lock assembly has failed, the control board will not receive that confirmation signal and will trigger the dr code.

Common failure points include a worn or broken door catch that no longer engages the latch properly, a faulty door lock assembly where the internal switch has failed electrically, damaged wiring between the door lock and the control board, or a door that is simply not fully closed. Diagnosis should begin by confirming the door is firmly pressed shut, then inspecting the door catch for visible damage. If the catch is intact and the door closes fully, the door lock assembly itself is the most likely component requiring replacement.

Source: manufacturer service documentation.

Common causes of dr

  1. 01

    Door not fully closed

    Wiring / connection

    The door may appear closed but is not fully latched. Press the door firmly until you hear or feel a click, then restart the cycle.

  2. 02

    Broken or worn door catch

    Part replacement

    The plastic door catch on the door itself can crack or wear down over time, preventing it from engaging the lock assembly. Inspect the catch for visible damage or deformation.

  3. 03

    Failed door lock assembly

    Part replacement

    The internal switch within the door lock assembly can fail electrically, meaning it no longer sends a closed-door signal to the control board even when the door is latched. If the catch is intact but the error persists, the lock assembly is the likely culprit.

  4. 04

    Damaged wiring or connector

    Wiring / connection

    The wiring harness connecting the door lock assembly to the control board can develop breaks or loose connections, interrupting the door-closed signal. Inspect the connector at the door lock for corrosion or looseness.

  5. 05

    Obstructions in the door seal area

    Wiring / connection

    Clothing or debris caught between the door and the rubber door gasket can prevent the door from closing fully and engaging the latch. Check the gasket area for any trapped items before assuming a component failure.

See the test procedure for each cause

Frequently asked questions about dr

What does dr mean on a Electrolux washer?
The dr code stands for door and indicates that the washer's control board is not receiving a closed-door signal from the door lock assembly. The machine requires a confirmed latched door before it will run a cycle. This can be caused by a door that is not fully closed, a broken door catch, or a faulty door lock assembly.
How do I fix the dr error code on my Electrolux washer?
Start by pressing the door firmly closed until it clicks and see if the error clears. Next, inspect the door catch on the door itself for cracks or damage, as a broken catch is a common cause. If the catch looks intact, the door lock assembly likely needs to be replaced. Check the wiring connector at the lock assembly as well, since a loose or corroded connection can also trigger this code.
Will resetting my Electrolux washer clear the dr error?
A reset may temporarily clear the code, but if there is a physical or electrical problem with the door latch or lock assembly, the error will return as soon as the next cycle begins. Resetting is useful only to confirm whether the door not being fully closed was the cause. If the code comes back, further diagnosis of the door catch and lock assembly is needed.
Is it safe to use my Electrolux washer when the dr code is showing?
No. The dr code is a safety lockout that prevents the washer from operating with an unconfirmed door latch. Running a washer with a faulty or open door lock creates a risk of water leaking from the door during a cycle. Do not attempt to bypass or force the machine to run until the door latch issue is resolved.
How much does it cost to fix a dr error on an Electrolux washer?
If only the door catch needs replacement, parts typically cost in the range of $10 to $30 depending on the model. A full door lock assembly replacement generally runs $40 to $100 in parts. If you hire a technician, expect to add $80 to $150 or more for labor, though door lock replacements are often a straightforward repair for experienced DIYers.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass