mypros+
Error code reference

Electrolux Washer Error Code EE6

Fan over voltage alarm

Electrolux codesElectrolux washer codes

Fan over voltage alarm - voltage input above 282Vrms for 20ms.

First step from the service manual

Check mains voltage; check fan control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EE6.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EE6 means on a Electrolux washer

The EE6 error code on an Electrolux washer indicates a fan over voltage alarm. This fault is triggered when the voltage input to the fan circuit rises above 282Vrms and remains at that level for at least 20 milliseconds. The fan referenced in this code is typically the motor control or inverter board cooling fan, which protects the drive electronics from heat damage. When the voltage feeding this fan exceeds the threshold, the control system flags the fault and may halt operation to prevent component damage.

The two primary areas to investigate are the incoming mains supply voltage and the fan control board itself. Abnormally high mains voltage from the utility supply is the most straightforward external cause. In some regions, voltage fluctuations or transient surges can push line voltage above the 282Vrms threshold, especially during periods of low grid load. A true RMS voltmeter should be used to check the supply at the wall outlet and at the machine terminals under load conditions.

If the mains voltage is within normal range, attention shifts to the fan control board. A failing control board can misread or generate incorrect voltage signals to the fan circuit, causing a false over voltage condition. Internal board component failure, such as a damaged voltage sensing circuit or shorted component, can produce this fault even when actual line voltage is normal. In either case, continuing to operate the washer with this fault active risks damage to the drive electronics.

Source: manufacturer service documentation.

Common causes of EE6

  1. 01

    High mains supply voltage

    Wiring / connection

    The incoming utility voltage may be elevated above normal levels, pushing the fan circuit input above the 282Vrms fault threshold. Check the outlet voltage with a true RMS voltmeter and compare against your local nominal supply standard.

  2. 02

    Voltage surge or transient spike

    Wiring / connection

    A brief but significant voltage spike from the power grid or from other appliances cycling on the same circuit can trigger the 20ms over voltage detection window. Inspect for shared circuit loads and consider whether the fault appeared during or after a power fluctuation.

  3. 03

    Faulty fan control board

    Part replacement

    The fan control board may have a damaged voltage sensing circuit or failed internal component that causes it to report an over voltage condition even when mains voltage is normal. If the supply voltage checks out correctly, the control board is the next suspect for replacement.

  4. 04

    Wiring fault or poor connection to fan board

    Wiring / connection

    Loose, corroded, or damaged wiring between the main control board and the fan control board can cause abnormal voltage readings. Inspect all connectors and harness segments leading to the fan control board for signs of arcing, corrosion, or mechanical damage.

  5. 05

    Failed main control board outputting incorrect voltage

    Part replacement

    If the main control board is malfunctioning, it may supply an out-of-range voltage signal to the fan circuit, triggering the EE6 alarm. This is typically diagnosed after confirming the mains supply and fan control board are both functioning correctly.

See the test procedure for each cause

Frequently asked questions about EE6

What does EE6 mean on a Electrolux washer?
EE6 is a fan over voltage alarm. It means the washer has detected a voltage input above 282Vrms lasting at least 20 milliseconds on the fan circuit. The washer stops to protect its electronics from damage. The fault points to either the incoming mains voltage being too high or a problem with the fan control board.
How do I fix the EE6 error on my Electrolux washer?
Start by measuring the mains supply voltage at the wall outlet using a true RMS voltmeter to confirm it is within the normal range for your region. If the supply voltage is normal, inspect the wiring and connectors leading to the fan control board for damage or loose connections. If those checks pass, the fan control board itself likely needs to be replaced. A qualified technician should handle board replacement and further electrical diagnostics.
Is it safe to keep using my washer when it shows EE6?
No, it is not safe to continue running the washer while EE6 is active. The fault indicates an over voltage condition that can damage the drive electronics and cooling fan components if the machine operates under these conditions. Leave the washer unplugged until the source of the fault has been identified and corrected.
Will resetting the washer clear the EE6 error?
A reset may temporarily clear the EE6 code, but if the underlying cause, such as high mains voltage or a faulty fan control board, has not been addressed, the fault will return. Simply resetting without diagnosing the root cause risks repeated fault triggering and potential component damage. Always resolve the cause before returning the machine to service.
How much does it cost to repair an EE6 error on an Electrolux washer?
Repair costs vary depending on the root cause. If the issue is high mains voltage, the fix may involve only an electrician visit or a surge protection device, typically ranging from $75 to $200. If the fan control board requires replacement, parts and labor combined can range from $150 to $400 depending on parts availability and local labor rates. Diagnosing the fault accurately before ordering parts will help avoid unnecessary expenses.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass