mypros+
Error code reference

Electrolux Washer Error Code 93

Console or main board control problem (incompatible machine configuration).

Electrolux codesElectrolux washer codes

Console or main board control problem (incompatible machine configuration).

First step from the service manual

Refer to test (11) - Check wiring between main control board and user interface board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 93.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 93 means on a Electrolux washer

Error code 93 on an Electrolux washer indicates a console or main board control problem specifically related to an incompatible machine configuration. This means the user interface board and the main control board are not communicating correctly or are not recognized as compatible with each other. The control system compares configuration data between both boards during startup or operation, and when that data does not match or cannot be validated, code 93 is triggered to prevent the machine from running in an undefined or unsafe state.

The two primary components involved are the main control board and the user interface (console) board, connected by a wiring harness. If either board has been replaced with an incorrect part, if the boards were sourced from different machine variants, or if firmware versions are mismatched, the configuration check will fail. Physical wiring faults between the two boards, including loose connectors, damaged pins, or broken wire insulation, can also disrupt the communication signal enough to produce this error even when the boards themselves are compatible.

The first diagnostic step is to inspect the wiring harness running between the main control board and the user interface board, as outlined in test 11 of the diagnostic procedure. Technicians should check for continuity, secure connector seating, and visible damage along the harness before assuming either board is defective. If wiring checks out, verifying that both boards carry matching configuration identifiers for the specific machine model is essential before replacing components.

Source: manufacturer service documentation.

Common causes of 93

  1. 01

    Loose or disconnected wiring harness between boards

    Wiring / connection

    The connector linking the main control board to the user interface board may have come loose or have a damaged pin. Inspect both ends of the harness for secure seating and any bent or corroded pins.

  2. 02

    Incompatible replacement board installed

    Part replacement

    If either the main control board or the user interface board was recently replaced, it may not match the configuration required by the other board. Confirm that any replacement part is specific to the exact model and variant of the washer.

  3. 03

    Damaged wiring harness between console and main board

    Part replacement

    Chafed, broken, or shorted wires along the harness running between the two boards can disrupt communication signals. Trace the full length of the harness and test for continuity and shorts.

  4. 04

    Faulty user interface board

    Part replacement

    The console board itself may have failed internally, causing it to report incorrect or unrecognized configuration data to the main control board. This is typically confirmed after wiring and compatibility checks have been cleared.

  5. 05

    Faulty main control board

    Part replacement

    The main control board may have failed in a way that prevents it from correctly reading or matching configuration data from the user interface board. This is usually the last component suspected after all wiring and the console board have been ruled out.

See the test procedure for each cause

Frequently asked questions about 93

What does 93 mean on a Electrolux washer?
Error code 93 on an Electrolux washer signals a console or main board control problem caused by an incompatible machine configuration. It means the main control board and the user interface board are not recognizing each other as compatible, preventing the washer from operating. This can be caused by a wiring fault between the two boards or by a board that does not match the machine's required configuration.
Can I fix error code 93 on my Electrolux washer myself?
The first step is to check the wiring harness between the main control board and the user interface board, which a knowledgeable DIYer can do by inspecting connectors for secure seating and visible damage. However, if the wiring checks out and a board needs to be replaced, it is critical to install the exact correct part for your model, as installing the wrong board is what causes this error in the first place. If you are not comfortable working with control boards and wiring, a technician is recommended.
Will resetting my Electrolux washer clear error code 93?
A simple power reset is unlikely to clear error code 93 permanently because it points to a hardware or configuration mismatch rather than a temporary software glitch. The underlying cause, whether it is a wiring fault or an incompatible board, must be corrected before the error will stop returning. You can attempt a reset to see if the code clears temporarily, but expect it to reappear if the root cause is not addressed.
Is it safe to use my Electrolux washer when error code 93 is displayed?
Error code 93 typically prevents the washer from completing its normal operation because the control system has detected that the boards are not communicating or configured correctly. Running the machine in this state is not advisable, as the control boards cannot reliably manage the wash cycle without proper communication. It is best to resolve the error before using the washer again.
How much does it cost to repair error code 93 on an Electrolux washer?
If the issue is only a loose or damaged wiring harness, repair costs can be relatively low, typically in the range of $75 to $150 for a service call and minor wiring repair. If a user interface board or main control board needs to be replaced, parts and labor combined can range from $200 to $450 or more depending on the specific board and local labor rates. Getting a diagnostic from a qualified technician before purchasing parts helps avoid buying an unnecessary or incorrect component.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass