mypros+
Model reference

Electrolux EFLS527UIW2

Washer

4 documents56 error codes6 service modes

Available documentation

Tech Sheet

  • Washer Tech Data Sheet24 pg
    Covers this model
  • Washer Tech Data Sheet24 pg
    Covers this model

Service Manual

  • EFLS527U Front-Load Washing Machine Service Manual12 pg
    Covers this model

Installation Guide

  • Front Load Washer Use & Care Guide48 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EFLS527UIW2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (56)

CodeMeaning
11Fill time too long.13Water leak in tub or in pressure sensor.21Water not pumping out fast enough.23Drain triac error.24Drain triac error sensing.31Electronic pressure switch error.32Pressure sensor calibration problem.35Pressure sensor indicates water overfill.38Air trap clogged.41Control board thinks the door switch is open.42Door lock device failure.43Door lock triac failure.44Door closed sensing failure.45Line door sensing failure.55Motor under speed (not available on 300 series, select models only).57High current on inverter (motor control).58High current on motor phase.59No spin signal for 3 seconds.5AHigh temperature on control due to overload (motor control).5BMotor control under voltage.5CHigh voltage experienced by motor control board.5DCommunication problem with motor control (message).5ECommunication problem from motor control (communication failure).5FMC (motor control) is continuously resetting.62Wash temperature too high.66Heater relay problem (on select models).68Current leakage to ground on heater or wiring (on select models).69Heater open (on select models).6AHeater relay sensing problem (on select models).71Drum water NTC failure (tub heater) (on select models).
View all 56 error codes
74Wash temperature does not increase.83Wrong selector reading.84Recirculation pump triac sensing failure which stops the cycle (on select…85Recirculation pump triac alarm which stops the cycle (on select models).86Incorrect UI selection table.87User interface micro-controller fault.88Concentrated wash pump triac alarm (on select models).91User interface protocol incongruence error.92User interface mother board protocol incongruence.93Console or main board control problem (incompatible machine configuration).94Main board control problem (incompatible cycle configuration).97Console or main board control problem (incompatible cycle configuration).98Incompatible motor control/main board.9CUser interface configuration problem.9ETouch sensor on user interface not responding.C1Flow meter is running when no valves are driven.F2Too much soap or wrong type of detergent.F4Flow meter is not running when valves are driven.F5Load unbalanced.F6Control reset.F9Hot valve warningH1/B1Frequency of power out of limits.H2/B2Supply voltage too high (incoming voltage).H3/B3Supply voltage too high (incoming voltage).HE/BEControl relay fault.HF/BFControl relay sense fault.

Service modes (6)

  • Demo Mode["1. Press power and look for console light up.","2. For Rotary Dial Cycle Select Washer
  • Diagnostic Mode["1
  • Error History (in Diagnostic Mode)["Navigate to the Error History test step within Diagnostic Mode."]
  • Error History (within Diagnostic Mode)["Navigate to the Error History test step within Diagnostic Mode.","The last 3 errors in memory are…
  • Factory Default Reset["1
  • Recall Last Error Code["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax