mypros+
Error code reference

Electrolux Washer Error Code 83

Wrong selector reading.

Electrolux codesElectrolux washer codes

Wrong selector reading.

First step from the service manual

Refer to test (10) - Check wiring between main control board and motor control board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 83.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 83 means on a Electrolux washer

Error code 83 on an Electrolux washer indicates a wrong selector reading, meaning the main control board is receiving an unexpected or invalid signal from the motor control board through the communication circuit between the two boards. This error points to a breakdown in the data exchange that allows the main control board to monitor and direct motor operation. When the selector signal falls outside the expected parameters, the control system flags the fault and halts operation to prevent potential damage to the drive system.

The most common root cause of error 83 is a wiring fault between the main control board and the motor control board. Damaged, corroded, or loose connector pins in the harness that links these two boards can interrupt or distort the selector signal, causing the control system to read an incorrect value. In some cases, the wiring harness may have been pinched during a previous repair or may have degraded over time due to vibration and heat exposure inside the machine cabinet.

If the wiring harness checks out correctly, one of the two control boards may be at fault. A failed motor control board can output an incorrect selector signal, and a failed main control board may misinterpret a valid signal. Diagnosis should follow a structured approach starting with a thorough inspection of the wiring and connectors between the two boards before condemning either board as defective.

Source: manufacturer service documentation.

Common causes of 83

  1. 01

    Loose or disconnected wiring harness connector

    Wiring / connection

    The connector between the main control board and the motor control board may have worked loose due to vibration. Inspect both ends of the harness for secure seating at each connector housing.

  2. 02

    Damaged or corroded wiring harness

    Part replacement

    Wires in the harness running between the two control boards may be pinched, broken internally, or have corroded terminals that interrupt the selector signal. A continuity test on each wire in the harness can confirm this.

  3. 03

    Faulty motor control board

    Part replacement

    If the wiring harness is intact and connections are secure, the motor control board may be outputting an incorrect or out-of-range selector signal. This board will need replacement if it fails functional testing.

  4. 04

    Faulty main control board

    Part replacement

    The main control board may be misreading a valid selector signal from the motor control board due to an internal component failure. This is typically diagnosed after the wiring and motor control board have been ruled out.

See the test procedure for each cause

Frequently asked questions about 83

What does 83 mean on a Electrolux washer?
Error code 83 on an Electrolux washer means the main control board has detected a wrong or invalid selector reading from the motor control board. This indicates a communication fault between the two boards, most often caused by a wiring issue. The washer stops operating to prevent further damage until the fault is resolved.
Can I fix error code 83 on my Electrolux washer myself?
A knowledgeable DIYer can start by checking that all wiring connectors between the main control board and the motor control board are fully seated and free of corrosion. If connectors are secure and the error persists, diagnosing and replacing a control board typically requires comfort with electronics and multimeter use. If you are unsure about working with control boards, a professional technician is recommended.
Will resetting my Electrolux washer clear error code 83?
A power reset by unplugging the washer for a few minutes may temporarily clear the error, but it will return if the underlying wiring or board fault has not been corrected. Error 83 reflects a detected hardware communication problem that requires physical diagnosis and repair to resolve permanently.
Is it safe to use my Electrolux washer when error code 83 appears?
It is not recommended to continue using the washer while error 83 is active. The machine has detected a fault in the communication between its control boards, which can affect motor operation and potentially cause additional damage if the washer is forced to run. Leave the washer unplugged until the fault is diagnosed and repaired.
How much does it cost to repair error code 83 on an Electrolux washer?
If the fix is simply reseating a wiring connector, the repair cost is minimal and may only involve a service call fee, typically in the range of $75 to $150. Replacing a wiring harness generally runs $100 to $250 including parts and labor. If a control board requires replacement, costs can range from $200 to $450 or more depending on which board is faulty and local labor rates.

Related Electrolux washer codes

All Electrolux washer codes
View all 231 Electrolux washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass