Skip to main content
Error code reference
Electrolux Dryer Error Codes
210 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
0x21Condense Pump Error-Wiring defective or Pump defective or Main Board defective.0x22Condense Pump Sensing Error-Main board defective.0x31Conductimetric Sensor Frequency Too High-Wiring defective or Main Board defective.0x32Conductimetric Sensor Frequency Too Low-Wiring defective or main board defective.0x45Door Closed Sensing Error-Main Board defective.0x55FCV Safety Error-Main board defective.0x56FCV Motor Plug Not Connected-Wiring defective or Motor defective or Main Board defective.0x57FCV Current Trip Failure-Wiring defective or Motor defective or Main Board defective.0x58FCV Over Current Failure-Wiring defective or Motor defective or Main Board defective.0x59FCV Motor Not Following-Main board defective.0x5AFCV Board Overheating-Wiring defective or Motor defective or Main Board defective.0x5BFCV Under Voltage Failure-Power supply problem or main board defective.0x5CFCV Over Voltage Failure-Power supply problem or main board defective.0x5DFCV Unknown Message Error-Main Board defective.0x5FFCV Power Module Error-Main board defective.0x62Heater Short Circuit Error-Heater Relay stuck open or closed or Wiring defective or…0x63Heater Error-Heater Relay stuck open or closed or Wiring defective or Main Board…0x64Heater Sensing Error-Main board defective.0x71Drying NTC Error-NTC1 failure or Wiring defective or Main Board defective.0x72Heater NTC Error-NTC2 failure or Wiring defective or Main Board defective.0x73Steamer NTC Error-NTC2 failure or Wiring defective or Main Board defective.0x83Selector Position Code Error-User Interface Board defective.0x86Selector Configuration Table Error-User Interface Board defective.0x87UI Board Microcontroller Self Test Failure-User Interface Board defective.0x91User Interface Communication Error-User Interface Board defective or Main Board defective…0x92User Interface Protocol Incongruence Error-Main Board incompatible with User Interface…0x93Machine Configuration Checksum Error-Wrong configuration data loaded, User Interface…0x94Cycle Configuration Checksum Error-Wrong configuration data loaded or Main Board…0x97Missing Program on CTF Error-Discrepancy between programme configuration data and…0x9CUser Interface Configuration Checksum Error-Discrepancy between programme configuration…0x9EUser Interface Touch Sensor Not Working-Humidity or Water on User Interface Board or User…0xB1Power Supply Frequency Out of Range-Power Supply Frequency out of configured range.0xB2Power Supply Amplitude Out of Range (Too High)-Line Voltage too high or Main Board fault.0xB3Power Supply Amplitude Out of Range (Too Low)-Line Voltage too Low or Main Board fault.0xB4Zero Watt Relay Error-Line connections in home faulty, wiring or Main Board defective.0xBDLine Safe Short Circuit Error-Main Board defective.0xBELine Safe Error-Main board defective.0xBFLine Safe Sensing Error-Main Board defective.0xF6Safety Reset Error-Main board defective.34Capacitive sensor values read by main control board are not within the predefined…35Capacitive sensor assembly communication problem with main control board (500 and 600…41Door opened at cycle start.42Door closed sensing error.51Drum motor relay error52Drum motor start sensing error53Drum motor centrifugal switch error54Drum motor sensing error61Heater relay error.63Heater short error.64Heater open error.65Thermostat open67Heater sensing error71NTC1 open error72NTC1 (SHORTED) error.73NTC2 open error74NTC2 (SHORTED) error.91User Interface communication problem with main board.92User Interface mother board protocol mismatch.93MCF checksum error94CCF checksum error97Missing program on CTF error9CUser Interface configuration checksum error9EUser Interface touch sensor not workingAL 50The motor has been overloaded.AL 97There is a disruption in internal communication between electronic elements of the unit.AL H0There is an issue with the power supply.B1Power supply frequency out of range.B2Power supply amplitude out of range (too HIGH voltage).B3Power supply amplitude out of range (too LOW voltage).B4Line wiring errorBDLine safe relay short circuit error.BELine safe errorBFLine safe sensing errorDEMO MODEDryer has been programmed to temporarily perform a repeating demo cycle instead of normal…E00No failure code experienced; indicates no error has been recorded.E10Problem with communication between EEPROM and the microprocessor.E11Problem with communications or memory did not check, one has become corrupted (Checksum…E12Problem reading or writing to the memory or input/output (Non fatal R/W error).E20Condense pump alarm (ENV06 platform)E21Condensation water filling pump alarmE22Condensation water filling pump detection alarmE24Control thermistor or its wiring is shorted (Control NTC Short Circuit).E25Control thermistor or its wiring is open (Control NTC Open Circuit).E30Conductimetric sensor frequency too high (ENV06)E31Contact Sensor frequency too high due to defective Electronic Control Board or foreign…E32Conductimetric sensor frequency too low (ENV06)E33Displayed in the last alarm if diagnostics position 8 is NOT OK (conductimetric sensor…E41Door opening solenoid supply triac defective.E42Sensing circuit of the door opening solenoid supply triac defective.E43Incongruency of the sensing signal of the door interlock.E45Door closed sensing alarmE4AClogged vent or restricted airflow detected, resulting in longer than normal drying times.E51Drum motor relay errorE52Drum motor thermal cut-off alarm (ENV06)E53Exhaust thermal limiter has tripped (open fuse), indicating possible airflow restriction…E54Motor jammed alarm (ENV06)E55Inverter board safety alarmE57Inverter is drawing too much current (>15 A)E58Inverter is drawing too much current (>4.5 A)E59No signal from tachometric generator for 3 secondsE5AOverheating on cooling dissipater for inverter (>88°C)E5BTemperature reading of control thermistor has not changed in a certain amount of time…E5CInput voltage is too highE5dData transfer error between inverter and main PCBE5ECommunication error between inverter and main PCBE5FInverter PCB fails to start the motorE5HInput voltage is lower than 175 VE60Heaters alarm (or compressor alarm for heat pump)E61Heater relay errorE62Heaters relay failure / compressor relay failure (ENV06)E63Compressor alarmE64Heaters sensing alarm / compressor sensing alarm (ENV06)E65High Limit Thermostat trip count too high due to high vent restriction, defective High…E66Thermal Limiter Open CircuitE67Heaters Sensing FailureE68Key (button) is stuck closed (active)E71Drying NTC1 alarmE72Steamer NTC2 alarmE73NTC 2 (Inlet Control Thermistor) open, disconnected, or main board fault.E74Motor Relay failure-motor relay stuck open or closed, or wiring defective.E81Error at the reset position of the program selector.E82Communication error between main electronics and display/control electronics.E83Incorrect selector dial positionE86Incorrect selector configurationE87Self-diagnosis of main circuit board faultyE8CThe safety (high limit) thermostat has tripped too many times within a certain period of…E91Communication Error between Electronic Control Board and Interface Board due to defective…E92User interface protocol incongruence errorE93Machine configuration checksum error-wrong configuration data loaded, Interface Board or…E94CCF checksum alarmE95Communication error between microprocessor and EEPROM.E97Missing program on CTF errorE98Inconsistent inverter board protocolE9AControl thermistor open or shorted; thermistor reading out of expected range.E9BUser interface external flash communication alarm.E9CUser interface checksum alarmE9DReal time clock alarm.E9EOne or more touch keys on the user interface does not workEA1CRM satellite board communication alarmEA2CRM satellite board protocol incongruence alarmEA3Voltage too low-line voltage too low or Electronic Control Board faulty.EA4Improper home wiringEA5Input board communication alarmEAFMicrocontroller has been reset by internal Watchdog timer (Watch Dog Reset).EB1Mains supply frequency outside acceptable limits.EB2Mains supply frequency too high.EB3Mains supply frequency too low.EBDLine safe relay short circuit errorEBELine safe errorEBFLine safe sensing errorEC1Power supply amplitude out of rangeEC2Power supply frequency out of rangeEC3Steamer heating-up timeout alarmEC4Steamer heater alarmEC5Steamer heater thermal cut-off alarm.EC6Steamer heater sensing alarmEC7Steam pump alarmEC8Steam pump diode alarmEC9Steam pump triac sensing alarmECAMissing steamer water alarmEF1Ventilation blocked errorEF3Max Timeout TimerEF6Microprocessor safety resetEF8Key StuckEH1Power supply frequency out of rangeEH2Power supply voltage out of range (too HIGH)EH3Power supply voltage out of range (too LOW)EH4Zero Watt relay alarmEHDCurrent leakage alarmEHESafety line alarmEHFSafety line sensing alarmErrError displayed when attempting to change programme or option after cycle start, or when…F 01An internal fault in the electronic control board.F 02Control temperature sensor open or shorted.F 03No heatF 04The drying time has exceeded the program time for that cycle.F 05A problem with the keypad.F-0Surface element faultF-1Surface element faultF-7Surface element faultF-8Surface element faultF2Bake/Broil/Clean Temperature Runaway AlarmF3Open Temperature SensorF4Shorted Temperature SensorF5Supervisory Relay Enable Open (cook modes)F6Missing AC Line Cycle DetectorF9Door Latch Supervisory (Door Latched)H1Power supply frequency out of range.H1/B1Power supply frequency out of range.H2Power supply amplitude out of range (too HIGH voltage).H2/B2Power supply amplitude out of range (too HIGH).H3Power supply amplitude out of range (too LOW voltage).H3/B3Power supply amplitude out of range (too LOW).H4Line wiring errorH4/B4Line wiring error.HALine safe relay short circuit error.HA/BDLine safe relay short circuit error.HELine safe errorHE/BELine safe error.HFLine safe sensing errorHF/BFLine safe sensing error.LOCControl lock is activated.Maximum program timeMachine has been running for its maximum time (3 hours) and has stopped, possibly due to…OverfullThe condensation water tank is full (T780), or the bottom water container is full because…PAUCycle has been interrupted/paused.PFA power failure to the control board has occurred.Sensor errorFault in the humidity sensor; may also appear if the machine is run with already-dry…Sensor faultFault in the humidity sensor; may also appear if running the machine with already-dry…Thermistor errorThermistor fault detected; thermistor may be open circuit, short-circuited, or…Thermistor faultOpen or short circuit in the thermistor; the thermistor may have become disconnected or…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Electrolux error codes
Common questions
How do I find the error code on my Electrolux Dryer?
Most Electrolux dryers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Electrolux dryers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.