mypros+
Error code reference

Electrolux Dryer Error Code 0xBD

Line Safe Short Circuit Error-Main Board defective.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 0xBD error code actually means

Your dryer's main control board has detected an internal electrical fault and is shutting down to prevent further damage or a safety hazard. This is not a sensor or wiring problem you can fix by checking connections. The control board itself has failed and needs to be replaced.

Diagnostic procedure

The full 0xBD procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace the Main Board and repeat the diagnostic cycle to check for any further errors.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 0xBD procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 0xBD

Ranked by how often they cause this code
  1. 1Failed Main Control Board
  2. 2Power Surge Damage
  3. 3Overheating of the Control Board
  4. 4Moisture or Condensation Intrusion

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 0xBD

What does 0xBD mean on a Electrolux dryer?
Error code 0xBD is a Line Safe Short Circuit Error, indicating that the main control board has detected an internal short circuit within its own circuitry. The board's built-in protective monitoring circuit has flagged itself as defective. This code means the dryer cannot safely continue operation and the main board must be replaced. Running the diagnostic cycle after replacement will confirm whether the issue is fully resolved.
Is it safe to use my Electrolux dryer when error 0xBD is showing?
No, you should not continue using the dryer while this error is active. The 0xBD code indicates an internal short circuit on the main board, which is an electrical fault condition. Operating the dryer in this state could pose a risk of further damage to the appliance or, in the worst case, an electrical safety hazard. Leave the dryer unplugged until the main board has been replaced.
How much does it cost to fix error code 0xBD on an Electrolux dryer?
The cost to resolve this error depends on whether you hire a technician or do it yourself. A replacement main control board for an Electrolux dryer typically costs in the range of $100 to $250 for the part alone, depending on the specific model. If you hire a technician, labor charges will add another $80 to $150 or more, bringing the total repair cost to roughly $180 to $400 in most cases.
Can I fix error code 0xBD myself?
The repair requires replacing the main control board, which is a task some experienced DIYers can perform by disconnecting power, accessing the board, and swapping the part. However, working near line voltage components in a dryer carries real electrical risk, so if you are not comfortable with appliance disassembly and electrical safety procedures, a qualified technician should handle the replacement. After installing the new board, a diagnostic cycle should be run to confirm no additional errors are present.
Will resetting my Electrolux dryer clear error code 0xBD?
A simple power reset will not clear error code 0xBD permanently. Because the fault is an internal short circuit within the main board itself, the board will continue to detect and report the same condition every time it powers on. The error will return until the defective main board is physically replaced.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass