mypros+
Error code reference

Electrolux Dryer Error Code 0x32

Conductimetric Sensor Frequency Too Low

Electrolux codesElectrolux dryer codes

Conductimetric Sensor Frequency Too Low – Wiring defective or main board defective.

First step from the service manual

Check that humidity sensor wiring terminals are connected properly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x32.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x32 means on a Electrolux dryer

Error code 0x32 on an Electrolux dryer indicates that the conductimetric (moisture) sensor is producing a frequency signal that falls below the expected operating threshold. The conductimetric sensor works by measuring the electrical conductivity of moisture on the drum's sensor bars as clothes tumble against them. This conductivity reading is converted into a frequency signal that the main control board interprets to determine how wet the load is. When that frequency reads too low, the board cannot accurately gauge moisture levels and flags the fault.

The two most likely root causes are a wiring fault between the sensor and the main board, or a failure of the main control board itself. A wiring defect can include loose terminal connections, corroded pins, a broken wire in the harness, or a short to ground that pulls the signal frequency down. Because the sensor relies on small electrical signals, even a partial connection loss or high-resistance joint in the harness can cause the frequency to drop below acceptable limits.

Before condemning the main board, a thorough inspection of the humidity sensor wiring harness is essential. Check that all terminals at the sensor end and the board end are fully seated, free of corrosion, and undamaged. Inspect the wire harness along its entire routing path for pinch points or heat damage. If the wiring checks out intact and properly connected, the main control board is the likely cause of the fault and will need to be replaced.

Source: manufacturer service documentation.

Common causes of 0x32

  1. 01

    Loose or Disconnected Sensor Wiring Terminals

    Wiring / connection

    The most frequent cause is a terminal that has partially pulled out of its connector at the humidity sensor or at the main board. Inspect both ends of the harness and press each terminal firmly into place to confirm a secure connection.

  2. 02

    Corroded or High-Resistance Wiring Connections

    Wiring / connection

    Moisture and heat inside the dryer cabinet can cause terminal pins to corrode over time, increasing resistance and reducing the signal frequency. Look for discoloration, oxidation, or pitting on the connector pins.

  3. 03

    Damaged Wiring Harness

    Part replacement

    A wire in the humidity sensor harness may be broken, pinched, or chafed through insulation at a routing point, causing an intermittent or low signal. Flex the harness along its full length while observing for any change in the fault condition.

  4. 04

    Faulty Conductimetric Sensor

    Part replacement

    If the sensor bars on the drum are heavily coated with fabric softener residue or the sensor itself has failed internally, it may produce an abnormally low frequency output. Clean the sensor bars with a mild abrasive and retest before replacing the sensor.

  5. 05

    Defective Main Control Board

    Part replacement

    If the wiring harness and sensor check out correctly but the code persists, the main control board's input circuit for the conductimetric sensor signal may have failed. Board replacement is typically required in this scenario.

See the test procedure for each cause

Frequently asked questions about 0x32

What does 0x32 mean on a Electrolux dryer?
Error code 0x32 means the conductimetric (moisture) sensor is producing a frequency signal that is too low for the main control board to process correctly. This points to either a wiring defect in the sensor circuit or a failure of the main control board itself. The dryer flags this code to prevent inaccurate drying cycles caused by unreliable moisture readings.
How do I fix error code 0x32 on my Electrolux dryer?
Start by unplugging the dryer and inspecting the wiring terminals at the humidity sensor and at the main control board, pressing each connector firmly to ensure a solid connection. Check the harness for any visible damage such as broken wires, pinched spots, or corrosion on the terminal pins. If the wiring appears intact, clean the sensor bars inside the drum with a mild abrasive to remove any residue buildup. If the fault remains after these steps, the main control board likely needs to be replaced by a qualified technician.
Is it safe to keep using my Electrolux dryer with error code 0x32 active?
Running the dryer with an active 0x32 code is not recommended for extended use. Because the moisture sensor cannot provide accurate readings, the dryer may run longer than necessary, potentially overheating the load or consuming excess energy. It is best to resolve the fault before continuing regular use.
Will resetting my Electrolux dryer clear error code 0x32?
A power reset by unplugging the dryer for a few minutes may temporarily clear the code, but it will return if the underlying wiring fault or board issue has not been corrected. A reset alone is not a repair and should only be used as part of the diagnostic process to observe whether the fault is consistent or intermittent.
How much does it cost to repair error code 0x32 on an Electrolux dryer?
If the fix involves only reseating or replacing a wiring harness, repair costs are typically in the range of $50 to $150 including labor. If the main control board needs to be replaced, parts and labor combined generally range from $200 to $450 depending on the specific model and local labor rates. Getting a diagnostic estimate from a technician before committing to a board replacement is advisable.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass