mypros+
Error code reference

Electrolux Dryer Error Code 0x57

FCV Current Trip Failure

Electrolux codesElectrolux dryer codes

FCV Current Trip Failure – Wiring defective or Motor defective or Main Board defective.

First step from the service manual

Check for mechanical blockage in the Motor, then verify Motor wiring terminals are connected properly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x57.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x57 means on a Electrolux dryer

Error code 0x57 on an Electrolux dryer indicates an FCV (Fan/Control Voltage) Current Trip Failure. This means the main control board has detected an abnormal current condition in the motor circuit, triggering a protective shutdown. The control board continuously monitors current draw through the motor circuit, and when current exceeds expected thresholds or drops in an unexpected pattern, this fault is logged. The three primary culprits are defective wiring, a failed drive motor, or a faulty main control board.

The diagnostic process begins with a physical inspection for mechanical blockage in the motor. A jammed drum, seized bearing, or foreign object lodged in the blower wheel can cause the motor to draw excessive current as it struggles against resistance. This overcurrent condition trips the FCV protection circuit on the board. After ruling out mechanical binding, the motor wiring terminals should be inspected for corrosion, loose connections, or damaged insulation that could cause intermittent shorts or open circuits.

If the motor spins freely and all wiring connections are secure and undamaged, the fault points to either the motor windings themselves or the main control board. A motor with degraded windings may draw abnormal current even under no-load conditions. If winding resistance values fall outside specification or the motor shows signs of overheating, motor replacement is warranted. If the motor tests within spec, the main board's motor control circuitry may be the source of the false trip, requiring board replacement.

Source: manufacturer service documentation.

Common causes of 0x57

  1. 01

    Mechanical blockage in the motor or blower

    Wiring / connection

    A foreign object in the blower wheel, a seized drum bearing, or a jammed drum can cause the motor to overload and trip the current protection circuit. Check that the drum spins freely by hand and inspect the blower housing for obstructions.

  2. 02

    Defective or loose motor wiring

    Wiring / connection

    Corroded terminals, loose connectors, or damaged wire insulation in the motor circuit can cause abnormal current readings that trigger this fault. Inspect all motor wiring harness connections for secure fit, burn marks, or fraying.

  3. 03

    Failed drive motor

    Part replacement

    A motor with degraded windings may draw excessive current even when spinning freely, triggering the FCV trip. If the motor shows signs of overheating, emits a burning smell, or measures outside resistance specification, it requires replacement.

  4. 04

    Faulty main control board

    Part replacement

    If the motor and wiring both check out, the motor control circuitry on the main board itself may be generating a false current trip signal. A defective board can misread motor current or fail to regulate voltage to the motor correctly.

See the test procedure for each cause

Frequently asked questions about 0x57

What does 0x57 mean on a Electrolux dryer?
Error code 0x57 indicates an FCV Current Trip Failure, meaning the control board detected an abnormal current condition in the motor circuit and shut the dryer down. This fault is associated with defective wiring, a blocked or failed drive motor, or a malfunctioning main control board. The dryer will not operate until the underlying cause is identified and corrected.
How do I fix error code 0x57 on my Electrolux dryer?
Start by checking for any mechanical blockage: rotate the drum by hand to confirm it moves freely and inspect the blower wheel for debris. Next, inspect all motor wiring terminals and connectors for loose, corroded, or damaged connections. If no physical or wiring issues are found, the motor or main control board will need to be tested and potentially replaced by a qualified technician.
Will resetting my Electrolux dryer clear the 0x57 error code?
A reset may temporarily clear the code, but if the underlying cause is not addressed, the fault will return as soon as the dryer attempts to run the motor again. Resetting without diagnosing the root cause is not a fix for this error. It is recommended to complete the full diagnostic process before relying on a reset.
Is it safe to use my Electrolux dryer while it is showing error code 0x57?
No, you should not continue operating the dryer while this error is active. The 0x57 fault indicates a motor circuit problem that could involve excessive current draw, which poses a risk of overheating or further component damage. The control board has shut the dryer down as a protective measure, and it should remain out of service until repaired.
How much does it cost to repair error code 0x57 on an Electrolux dryer?
Repair costs vary depending on which component is at fault. Wiring repairs or terminal cleaning are typically the least expensive, often covered mostly by labor costs in the range of $75 to $150. A replacement drive motor can add $100 to $250 in parts, while a new main control board can range from $150 to $350 in parts depending on the model. A diagnostic service call will help identify which component needs to be replaced before committing to a repair.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass