mypros+
Error code reference

Electrolux Dryer Error Code 0x58

FCV Over Current Failure

Electrolux codesElectrolux dryer codes

FCV Over Current Failure – Wiring defective or Motor defective or Main Board defective.

First step from the service manual

Check for mechanical blockage in the Motor, then verify Motor wiring terminals are connected properly.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 0x58.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0x58 means on a Electrolux dryer

Error code 0x58 on an Electrolux dryer indicates an FCV (Fan/Control Voltage) Over Current Failure. This code is triggered when the main control board detects an excessive current draw through the motor circuit, exceeding the threshold the board is designed to handle. The control system continuously monitors motor current during operation, and when that current spikes beyond normal operating parameters, the board registers this fault and shuts down the motor circuit to prevent further damage.

The three primary causes identified for this fault are defective wiring, a defective motor, or a defective main control board. A mechanical blockage in the motor is the first thing to rule out, since a seized or restricted drum motor will draw significantly higher current as it struggles against the obstruction. This increased load can mimic a motor failure and is the easiest condition to diagnose and correct without parts replacement.

If no blockage is found, the motor wiring harness and terminal connections should be inspected closely. Loose, corroded, or damaged terminals can create intermittent resistance spikes that produce over-current conditions. A motor with failed windings or damaged bearings will also draw excessive current under load. If both the motor and wiring check out within specification, the main control board itself may be misreading current levels or failing to regulate the motor circuit properly, making it the final component to suspect.

Source: manufacturer service documentation.

Common causes of 0x58

  1. 01

    Mechanical blockage in the motor or drum

    Wiring / connection

    A foreign object or seized bearing can prevent the motor from turning freely, causing it to draw excessive current. Check the drum for obstructions and try rotating it by hand to feel for unusual resistance.

  2. 02

    Defective or damaged motor wiring

    Wiring / connection

    Loose, corroded, or broken terminals in the motor wiring harness can create resistance spikes or short circuits that trigger an over-current condition. Inspect all motor wiring terminals for proper seating, corrosion, and visible damage.

  3. 03

    Failed drive motor

    Part replacement

    A motor with damaged windings or worn bearings will draw abnormally high current during operation, consistently triggering this fault. If the motor runs hot, hums without turning, or shows resistance values outside specification, it likely needs replacement.

  4. 04

    Defective main control board

    Part replacement

    If the motor and all wiring test within normal parameters, the main control board may be the source of the fault, either misreading current levels or failing to properly regulate the motor circuit. Board failure is typically diagnosed by elimination after all other components are cleared.

See the test procedure for each cause

Frequently asked questions about 0x58

What does 0x58 mean on a Electrolux dryer?
Code 0x58 indicates an FCV Over Current Failure, meaning the control board has detected that the motor circuit is drawing more current than it should. The dryer shuts down to protect itself from further damage. The fault points to one of three causes: a wiring defect in the motor circuit, a failing or seized motor, or a defective main control board.
How do I fix error code 0x58 on my Electrolux dryer?
Start by checking for any mechanical blockage in the drum or motor, since an obstruction is the simplest and most common cause of this fault. Next, inspect the motor wiring terminals to confirm they are fully connected and free of corrosion or damage. If no blockage or wiring issue is found, the motor itself or the main control board will need to be tested and likely replaced by a qualified technician.
Will resetting the dryer clear error code 0x58?
A reset may temporarily clear the code, but if the underlying cause is not corrected, the fault will return as soon as the dryer attempts to run the motor again. Resetting without diagnosing and fixing the root cause risks additional damage to the motor or control board. The reset should only be used as a step in the diagnostic process, not as a repair.
Is it safe to use my Electrolux dryer when it shows error code 0x58?
No, you should not continue operating the dryer while this code is active. An over-current condition in the motor circuit can cause wiring to overheat, potentially damaging additional components or creating a fire risk. Keep the dryer off until the fault has been diagnosed and the cause corrected.
How much does it cost to repair error code 0x58 on an Electrolux dryer?
Repair costs depend on which component is at fault. If a wiring issue is the cause, costs may be limited to a service call fee in the range of $75 to $150. A motor replacement typically runs between $150 and $350 including parts and labor. A main control board replacement can range from $200 to $450 depending on parts availability and local labor rates.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass