mypros+
Error code reference

Electrolux Dryer Error Code EC2

Power supply frequency out of range

Electrolux codesElectrolux dryer codes

Power supply frequency out of range - wiring failure or satellite board failure.

First step from the service manual

Check wiring and satellite board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EC2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EC2 means on a Electrolux dryer

The EC2 error code on an Electrolux dryer indicates that the control system has detected a power supply frequency outside of the acceptable operating range. The dryer's satellite board continuously monitors the incoming AC frequency, which should be a stable 60 Hz in North America. When the satellite board reads a frequency that deviates significantly from this expected value, it triggers EC2 to alert the technician that something in the power delivery or monitoring circuit has failed.

The satellite board is a secondary control module that handles specific monitoring and communication tasks, including power quality sensing. A wiring failure between the main control board and the satellite board can disrupt the frequency signal, causing the board to report incorrect or absent readings. Loose connectors, damaged wire harnesses, or corroded terminals in this circuit are common contributors to the fault.

In some cases, the satellite board itself has failed internally and is misreading or failing to read the incoming frequency correctly, even when the power supply and wiring are intact. Because the diagnostic path targets both wiring and the satellite board, a systematic inspection should begin with a thorough visual and continuity check of all wiring connected to the satellite board before condemning the board itself.

Source: manufacturer service documentation.

Common causes of EC2

  1. 01

    Loose or damaged wiring to satellite board

    Wiring / connection

    Wiring connectors between the main control board and the satellite board can loosen, corrode, or sustain damage over time. Inspect all harness connectors for secure seating, corrosion, and broken wires.

  2. 02

    Failed satellite board

    Part replacement

    The satellite board itself may have failed internally, causing it to misread or stop reading the incoming power frequency. If wiring checks out, the satellite board will need to be replaced.

  3. 03

    Damaged wire harness

    Part replacement

    The wire harness routing from the power input circuit to the satellite board can be pinched, abraded, or broken, interrupting the frequency signal. A continuity test along the harness will help identify any open or shorted sections.

  4. 04

    Poor electrical connection at terminal block

    Wiring / connection

    A loose or corroded connection at the dryer's terminal block can cause voltage instability that affects frequency readings at the satellite board. Check that all terminal block connections are tight and free of corrosion.

See the test procedure for each cause

Frequently asked questions about EC2

What does EC2 mean on a Electrolux dryer?
EC2 means the dryer has detected a power supply frequency outside of its expected operating range. The fault points to either a wiring failure or a satellite board failure within the dryer. A technician should inspect the wiring connections to the satellite board and test the board itself to determine the root cause.
Can I fix the EC2 error on my Electrolux dryer myself?
A knowledgeable DIYer can begin by checking that all wire harness connectors leading to the satellite board are firmly seated and free of corrosion. If the wiring appears intact, replacing the satellite board is the next step, which requires sourcing the correct replacement part and comfort working with appliance electronics. If you are unsure about working inside the dryer, a qualified appliance technician is recommended.
Will resetting the dryer clear the EC2 error code?
A reset may temporarily clear the EC2 code, but it will return if the underlying wiring fault or satellite board failure has not been corrected. Resetting without repairing the root cause is not a lasting solution. The code needs to be resolved through proper diagnosis and repair of the wiring or satellite board.
Is it safe to use my Electrolux dryer when the EC2 error is displayed?
It is not recommended to continue operating the dryer while EC2 is active, as the error indicates a problem with how the control system is monitoring incoming power. Running the dryer in this condition could mask other developing issues. Have the wiring and satellite board inspected before resuming normal use.
How much does it cost to repair an EC2 error on an Electrolux dryer?
If the issue is a loose or corroded wiring connection, repair costs may only involve a service call fee, typically in the range of $75 to $150. If the satellite board requires replacement, parts and labor combined can range from $150 to $350 or more depending on your location and the specific model. Getting a diagnostic estimate from a technician before authorizing repairs is always a good approach.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass