mypros+
Model reference

Electrolux EDR2000JEWEL

Dryer

1 document63 error codes12 service modes

Available documentation

Service Manual

  • DRYERS ALARMS & DIAGNOSTIC - TD Electronic Platform Collection59 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EDR2000JEWEL.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (63)

CodeMeaning
E00No alarm condition has occurred.E20Condense pump alarm (ENV06 platform)E21Canister fill pump triac faulty.E22Condense pump sensing alarm (ENV06 platform)E30Conductimetric sensor frequency too high (ENV06)E31Conductimetric sensor signal frequency too high.E32Conductimetric sensor frequency too low (ENV06)E41Power triac of door opening coil faulty.E42Triac sensing circuit for powering the door opening coil faulty.E43Incongruency of the sensing signal of the door interlock.E45Door closed sensing alarmE51Motor power triac short-circuited.E52Drum motor thermal cut-off alarm (ENV06)E53Motor triac sensing circuit faulty.E54Motor inoperational (jammed or unable to start).E57FCV current trip failureE58FCV over current failure.E59FCV not following failure.E5BFCV under voltage failure.E5CFCV over voltage failure.E5DFCV unknown message failure.E5EWrong FCV to main board communication failure.E5FFCV failure (general).E60Heaters alarm (or compressor alarm for heat pump)E61Insufficient heating (maximum time exceeded).E62Power relay to heater unit faulty.E63Heaters auto-reset thermostat / compressor auto thermal alarm (ENV06).E64Heaters sensing alarm / compressor sensing alarm (ENV06)E65Main fan alarmE66Main fan thermal cut-off alarm
View all 63 error codes
E67Main fan triac sensing alarmE71Drying NTC1 alarmE72Steamer NTC2 alarmE82Wrong reset position on selectorE83Wrong selector codeE91User interface communication alarm (ENV06)E92User interface protocol incongruence alarmE93MCF checksum alarmE94Error in the configuration of the drying cycle (EEPROM configuration incorrect).E95Communication error between microprocessor and EEPROM.E97Missing program on CTF alarmE9BUser interface external flash communication alarm.E9CUser interface configuration checksum alarm.E9DReal time clock alarm.EA1CRM satellite board communication alarmEA2CRM satellite board protocol incongruence alarmEA5Input board communication alarmEB1Power frequency to appliance out of limits.EB2Power voltage too high.EB3Power voltage too low.EC1Power supply amplitude out of rangeEC2Power supply frequency out of rangeEC3Steamer heating-up timeout alarmEC4Steamer heater alarmEC5Steamer heater thermal cut-off alarm.EC6Steamer heater sensing alarmEC7Steam pump alarmEC8Steam pump diode alarmEC9Steam pump triac sensing alarmECAMissing steamer water alarmEH1Power supply frequency out of range (ENV06 equivalent of EB1).EH2Power supply voltage too high (ENV06 equivalent of EB2).EH3Power supply voltage too low (ENV06 equivalent of EB3).

Service modes (12)

  • Alarm Cancellation - EDR 1000["Access diagnostics mode and turn the programme selector knob to the eleventh position (alarm…
  • Alarm Cancellation - EDR 2000 / EDR 2000 JEWEL["Access diagnostics mode and turn the programme selector knob to the eleventh position.","Press…
  • Alarm Cancellation - EDR 2000 CLUB DISPLAY["Access diagnostic mode and turn the programme selector knob to the eleventh position.","Press…
  • Alarm Cancellation - ENV06["Turn the programme selector knob clockwise to the alarm display position (avoid stopping at other…
  • Diagnostic Mode - EDR 1000 / EDR 2000 / EDR 2000 JEWEL / EDR 2000 CLUB DISPLAY["Ensure the appliance is switched OFF.","Press START/PAUSE and the option buttons…
  • Diagnostic Mode - ENV06 / ENV06 AEG / ENV06 CATALOGUE / ENV06 ACTION / ENV06 INPUT["Press the defined combination key (START + the nearest key on the left) and keep them…
  • Diagnostic Mode - ENV06 / ENV06 AEG CLOTHES REFRESHMENT["Press the defined combination key (START + the nearest key on the left) and keep them…
  • Diagnostic Mode - ENV06 HP / ENV06 AEG HP (Heat Pump)["Press the defined combination key (START + the nearest key on the left) and keep them…
  • Rapid Alarm Reading - EDR 1000["Press START/PAUSE and any one of the option buttons simultaneously for at least two…
  • Rapid Alarm Reading - EDR 2000["Press button 6 (start/pause) and button 4 simultaneously for at least 5 seconds.","The display…
  • Rapid Alarm Reading - EDR 2000 CLUB DISPLAY["Press buttons 8 and 7 simultaneously for at least 5 seconds.","The LCD display shows the last…
  • Rapid Alarm Reading - EDR 2000 JEWEL["Press button 6 (start/pause) and button 4 simultaneously for at least 5 seconds.","The display…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux dryer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax