mypros+
Error code reference

Electrolux Dryer Error Code E41

Door opening solenoid supply triac defective.

Electrolux codesElectrolux dryer codes

Door opening solenoid supply triac defective.

First step from the service manual

Check wiring and main electronics board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E41.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E41 means on a Electrolux dryer

The E41 error code on an Electrolux dryer indicates that the supply triac controlling the door opening solenoid has been detected as defective. A triac is a semiconductor switching device located on the main electronics board that controls the flow of AC power to specific components. In this case, the triac responsible for energizing the door solenoid circuit has failed, meaning the control board can no longer reliably switch power to the solenoid as commanded.

The door opening solenoid is part of the door latch or release mechanism on the dryer. When the triac shorts or fails open, the electronics board loses the ability to properly control the solenoid, which can prevent normal door operation. A shorted triac may allow continuous current flow to the solenoid even when it should be off, while an open triac failure means the solenoid receives no power at all. Either failure condition triggers the E41 fault.

Diagnosis should begin with a thorough inspection of the wiring harness connecting the door solenoid circuit to the main electronics board. Look for chafed insulation, loose connector pins, or burned terminals that could cause a short or open circuit. If the wiring checks out clean, the fault points to the main electronics board itself, where the failed triac resides. In most cases, the entire main board requires replacement since individual triacs are surface-mounted components that are difficult to source and replace at the component level.

Source: manufacturer service documentation.

Common causes of E41

  1. 01

    Failed supply triac on main electronics board

    Part replacement

    The triac component on the main board that switches power to the door solenoid has shorted or failed open. This is the most direct cause of the E41 fault and typically requires replacing the main electronics board.

  2. 02

    Wiring harness damage or loose connector

    Wiring / connection

    A damaged wire, frayed insulation, or loose connector pin in the door solenoid circuit can create a short or open condition that mimics a triac failure. Inspect all wiring and connector terminals between the door solenoid and the control board before condemning the board.

  3. 03

    Door solenoid short circuit

    Part replacement

    A failed or internally shorted door solenoid can draw excessive current through the triac, causing it to fail. If the board shows signs of heat damage near the triac, test the solenoid resistance to check for a winding short.

  4. 04

    Burnt or corroded connector terminals

    Wiring / connection

    Overheated or oxidized terminals at the board connector or solenoid plug can increase resistance in the circuit, leading to erratic switching behavior and triggering the fault code. Clean or replace any corroded connectors as part of the diagnostic process.

See the test procedure for each cause

Frequently asked questions about E41

What does E41 mean on a Electrolux dryer?
E41 on an Electrolux dryer means the supply triac for the door opening solenoid has been detected as defective. The triac is an electronic switching component on the main control board that controls power to the door solenoid. When this component fails, the dryer cannot properly operate the door latch mechanism and displays the E41 fault.
Can I fix the E41 error myself on my Electrolux dryer?
A knowledgeable DIYer can start by inspecting the wiring harness and connectors between the door solenoid and the main electronics board for any visible damage, loose pins, or burnt terminals. If the wiring is intact, the repair typically requires replacing the main electronics board, which involves working with line voltage components. If you are not comfortable working with electrical components, a qualified technician should perform this repair.
Is it safe to use my Electrolux dryer when E41 is displayed?
It is not recommended to continue using the dryer while the E41 code is active. A defective triac in the door solenoid circuit can result in unpredictable door latch behavior, and a shorted triac may keep voltage applied to components even when the dryer is commanded to stop. Stop using the dryer and have the fault diagnosed before running further cycles.
How much does it cost to repair an E41 error on an Electrolux dryer?
Repair costs depend on whether the issue is a wiring problem or requires a full main electronics board replacement. If only wiring or connectors need attention, costs could be minimal, covering only labor. A main electronics board replacement typically runs between $150 and $400 including parts and labor, depending on the specific model and service rates in your area.
Will resetting my Electrolux dryer clear the E41 error code?
A power reset may temporarily clear the E41 code from the display, but the fault will return if the underlying hardware problem has not been resolved. Because E41 points to a defective triac or wiring fault rather than a soft error, resetting alone is not a fix. The root cause in the wiring or on the main electronics board must be addressed to permanently clear the code.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass