mypros+
Model reference

Electrolux EIED2CAQSW00

Dryer

4 documents57 error codes7 service modes

Available documentation

Service Manual

  • ELECTRIC DRYER - CABINET/DRUM Service Manual12 pg
    Covers this model
  • Technical Service Manual 2015 Urban Vent Less Dryer62 pg
    Covers this model

Installation Guide

  • Installation Instructions - Front Load Dryer44 pg
    Covers this model
  • Use & Care Guide / Guide D'utilisation Et D'entretien / GuÍa De Uso Y Cuidado18 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux EIED2CAQSW00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (57)

CodeMeaning
E00No alarm stored (displayed after alarm memory has been cleared).E11Door closed sensing alarmE21Condensation water filling pump faultE22Condensation water filling pump detection alarmE31Humidity sensor conductivity frequency too high.E32Humidity sensor conductivity frequency too low.E33Oscillation frequency is out of range (main board failure).E34Oscillation frequency is out of range (main board failure).E41NTC reading out of range.E42NTC failure or wiring failure.E43NTC circuit reading error on main board.E44Relay fault in the compressor detection circuit (main board failure).E45Compressor faultE46Compressor short-circuited.E47Compressor current leakage.E48Compressor thermal cut-out has triggered.E49Compressor 'sensing' circuit fault.E4ACompressor short-circuited.E4BCompressor alarm.E4CCompressor 'sensing' circuit fault.E51Motor faultE52No signal from motor tachometer generator for 3 secondsE53Communication error between motor control board (inverter) and main board.E54Abnormal motor operation (overloaded)E55Motor blockedE56Motor 'sensing' circuit fault.E57Inverter is drawing too much current (>15A).E58Inverter is drawing too much current (>4.5A).E59Inverter board safety alarm.E5AOverheating on heat dissipator for inverter (>88°C).
View all 57 error codes
E5BInput voltage too lowE5CData transfer error between Inverter and Main board.E5DMotor power supply short-circuited.E5EMotor thermal cut-out triggered.E5FCurrent leakage of any actuators.E5HSafety time alarm.E5KSafety sensing time alarm.E5LCurrent leakage alarm (zero relay).E61Overheating on heat dissipator for inverter (>88°C).E62NTC wiring fault, selector position code not recognized, main board selector…E71NTC wiring fault or NTC failure.E72Incorrect selector configurationE91User interface board communication alarmE92Inconsistent user interface board protocolE93Configuration alarmE94Inconsistent user interface board protocolE95User interface board checksum alarmE97Incorrect selector configuration (inconsistent)E98Missing program on cycle test or wrong cycle selector configurationE9FUser interface checksum alarmEA1DSP on main board (positioning of drum does not work).EA2DSP on main board (positioning of drum does not work).EH1Power supply frequency out of range.EH2Input voltage too high (>330V)EH3Input voltage too low (<175V)EHENTC on main-board self-diagnostics or main circuit board fault.EHFMicroprocessor safety reset

Service modes (7)

  • Child Lock["Simultaneously press the designated keys (dry time and wrinkle release) and hold until you hear a…
  • Clear Stored Alarms["Start diagnostics mode.","Turn the programme selector clockwise to position ten.","Press the…
  • Control Lock["Press dry time and wrinkle release at the same time and hold until the lock indicator is lit."]
  • Demo Mode["Turn on the dryer at the ON/OFF push button.","Select the second programme in the top left…
  • Diagnostics["Turn on the tumble dryer at the ON/OFF button.","Wait for the LEDs to be lit and for the buzzer…
  • Diagnostics Position 1 - User Interface Test["Enter diagnostics mode.","Set selector to position 1.","Press a button and the code is shown on…
  • Read Stored Alarms["Access diagnostics mode.","Turn the programme selector dial clockwise to the tenth…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux dryer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax