mypros+
Error code reference

Electrolux Dryer Error Code E93

Machine configuration checksum error

Electrolux codesElectrolux dryer codes

Machine configuration checksum error – wrong configuration data loaded, Interface Board or Electronic Control Board or wiring defective.

First step from the service manual

Check if correct Interface Board and console are installed. Replace Interface Board and/or console.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E93.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E93 means on a Electrolux dryer

Error code E93 on an Electrolux dryer indicates a machine configuration checksum error. This means the Electronic Control Board has detected a mismatch or corruption in the configuration data it reads from the Interface Board. During startup, the control system performs a checksum verification to confirm that the installed Interface Board matches the expected configuration for that specific dryer model. If the data does not match or fails the checksum test, the dryer halts operation and displays E93.

The most common cause is an incorrect Interface Board or console assembly installed in the unit, which can happen after a previous repair using a mismatched component. A defective Interface Board that has developed an internal fault can also cause the configuration data to appear corrupted, even if the correct part number was originally installed. Wiring harness faults between the Interface Board and the Electronic Control Board, such as damaged connectors, broken conductors, or poor contact at pin terminals, can also disrupt the data signal and trigger this error.

Because this error is rooted in the communication and configuration layer between the two main control components, mechanical components like the motor, heating element, or sensors are not involved. Diagnosis focuses on verifying component compatibility, inspecting wiring integrity, and replacing the Interface Board or Electronic Control Board as needed. Simply resetting the dryer typically will not clear E93 if the underlying hardware mismatch or fault remains present.

Source: manufacturer service documentation.

Common causes of E93

  1. 01

    Incorrect Interface Board or console installed

    Part replacement

    If the Interface Board or console assembly was previously replaced with a part that does not match the dryer model, the control system will fail its configuration check and display E93. Verify the part number of the installed Interface Board matches the specific model requirements.

  2. 02

    Defective Interface Board

    Part replacement

    The Interface Board itself may have developed an internal fault that corrupts the configuration data it provides to the Electronic Control Board. If the part number is confirmed correct but E93 persists, the Interface Board is the most likely replacement candidate.

  3. 03

    Wiring harness fault between boards

    Wiring / connection

    Damaged wiring, corroded connector pins, or loose terminal connections between the Interface Board and the Electronic Control Board can interrupt the configuration data signal and trigger this error. Inspect the harness and connectors carefully for visible damage or poor seating.

  4. 04

    Defective Electronic Control Board

    Part replacement

    If the wiring and Interface Board have both been confirmed good, the Electronic Control Board may be unable to correctly read or validate the configuration data. Replacing the Electronic Control Board is the next step if other causes are ruled out.

See the test procedure for each cause

Frequently asked questions about E93

What does E93 mean on a Electrolux dryer?
E93 is a machine configuration checksum error, meaning the dryer's Electronic Control Board has detected that the configuration data from the Interface Board is missing, incorrect, or corrupted. This is typically caused by a mismatched Interface Board, a faulty Interface Board, or a wiring fault between the two control components. The dryer will not run normally while this error is active.
Will resetting my Electrolux dryer clear the E93 error?
A reset will not permanently clear E93 if the underlying hardware problem is still present. Because the error is triggered every time the control system performs its configuration check at startup, it will return as long as a mismatched or defective Interface Board, Electronic Control Board, or faulty wiring remains in the unit. The root cause must be corrected first.
Is it safe to use my Electrolux dryer while E93 is displayed?
The dryer will typically not operate normally while E93 is active, as the control system halts operation when it detects a configuration failure. You should not attempt to bypass or force the dryer to run in this state. Continued use attempts without resolving the error could potentially cause further damage to the control components.
How do I fix the E93 error on my Electrolux dryer?
Start by confirming that the Interface Board and console installed in the dryer are the correct parts for your specific model. Next, inspect all wiring and connectors between the Interface Board and the Electronic Control Board for damage or poor connections. If the parts are confirmed correct and wiring is intact, replacing the Interface Board is the most likely fix. If the error persists after that, replacing the Electronic Control Board may be necessary.
How much does it cost to repair an E93 error on an Electrolux dryer?
Repair costs vary depending on which component needs to be replaced. An Interface Board replacement typically ranges from around 80 to 200 dollars for the part alone, while an Electronic Control Board can range from 100 to 300 dollars or more depending on the model. Adding professional labor costs will increase the total, generally ranging from 150 to 500 dollars or higher depending on your location and the technician's rates.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass