mypros+
Error code reference

Electrolux Dryer Error Code E5F

Inverter PCB fails to start the motor

Electrolux codesElectrolux dryer codes

Inverter PCB fails to start the motor — faulty wiring, inverter board faulty, or main board faulty.

First step from the service manual

Check wiring, inverter board, and main board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E5F.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E5F means on a Electrolux dryer

The E5F error code on an Electrolux dryer indicates that the inverter PCB (printed circuit board) has failed to start the drum motor. This code points to a communication or power delivery breakdown in the motor drive system, which relies on the inverter board to convert and regulate electrical power before it reaches the motor. When the inverter board cannot successfully initiate motor operation, the dryer halts the cycle and triggers this fault to prevent mechanical damage.

The three primary suspects in an E5F fault are the wiring harness connecting the inverter board and main board, the inverter board itself, and the main control board. Damaged, corroded, or disconnected wiring between these components can interrupt the control signals needed to start the motor. A failed inverter board may be unable to generate or regulate the correct output voltage for the motor. Similarly, a faulty main board may fail to send the proper startup command to the inverter board in the first place.

Diagnosis should begin with a thorough visual and physical inspection of all wiring between the main board and inverter board, checking for loose connectors, burnt terminals, or pinched wires. If wiring is intact, the inverter board should be tested or replaced, as it is generally more prone to failure than the main board. If substituting the inverter board does not resolve the fault, attention should turn to the main control board.

Source: manufacturer service documentation.

Common causes of E5F

  1. 01

    Loose or damaged wiring harness

    Wiring / connection

    Wiring between the inverter board and main board can become loose, corroded, or damaged over time. Inspect all connectors for secure seating, burnt contacts, or visible wire damage.

  2. 02

    Faulty inverter PCB

    Part replacement

    The inverter board is responsible for driving the motor and is a common failure point in this error. If wiring checks out, the inverter board likely needs replacement.

  3. 03

    Faulty main control board

    Part replacement

    If the main board fails to send the correct startup signal to the inverter board, the motor will not start and E5F will be triggered. This is typically diagnosed after ruling out wiring and the inverter board.

  4. 04

    Burnt or corroded connector terminals

    Wiring / connection

    Even when wires appear intact, the connector terminals at the board ends can oxidize or burn, creating high resistance that disrupts communication. Clean or replace affected connectors as needed.

See the test procedure for each cause

Frequently asked questions about E5F

What does E5F mean on a Electrolux dryer?
E5F means the inverter PCB failed to start the drum motor. The fault is related to the motor drive system and can be caused by faulty wiring between the boards, a failed inverter board, or a failed main control board. The dryer will not operate until the fault is resolved.
Can I fix an E5F error on my Electrolux dryer myself?
A knowledgeable DIYer can start by inspecting and reseating all wiring connectors between the inverter board and main board, which requires no parts and may resolve the fault. If the issue is a failed inverter board or main board, replacing those components is more involved and requires comfort working with electronics inside the appliance. If you are not confident working with internal dryer components, a professional technician is recommended.
Is it safe to keep using my dryer when E5F is displayed?
No, the dryer will not run while this error is active, so continued use is not possible until the fault is cleared. Attempting to bypass the error without addressing the root cause could risk further damage to the motor or control boards. Address the underlying problem before resuming operation.
How much does it cost to repair an E5F error on an Electrolux dryer?
Repair costs vary depending on which component has failed. A wiring repair may cost relatively little, while an inverter board replacement typically ranges from $100 to $250 in parts alone. A main control board replacement can range from $150 to $350 or more. Adding professional labor costs will increase the total, generally ranging from $100 to $200 depending on your location and the technician.
Will resetting my Electrolux dryer clear the E5F error code?
Resetting the dryer by unplugging it for a few minutes may temporarily clear the code, but the fault will return if the underlying cause is not repaired. E5F is triggered by a hardware failure in the motor start circuit, so a reset alone is not a fix. Inspect wiring and test or replace the inverter board or main board as needed to permanently resolve the error.

Related Electrolux dryer codes

All Electrolux dryer codes
View all 209 Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass